Follow us on Pinterest
Welcome, Guest! Log In  |  Join Now
More
Close

Magazine Changes and Updates

Pages in this Story:
Newsstand specials
Newsstand Specials
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
1991 335 Great Shop Tips 2 Quick 'N' Easy Bandsaw Extension Table The blade kerf for the bandsaw extension table can be made as shown, by cutting a kerf in from the left-hand side of the plywood table slightly wider than the blade. Or, an easier way to do this would be to slide the wood table through the blade, leaving a kerf behind the blade in the clamped-down extension table.
1993 Sensational Gifts You Can Build 80 Quilt Rack Bill of Materials: Part K quantity 1
1994 Outdoor projects 30 Adirondack Rocker Note: Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 34.
97/99 Country Workshop 52 Grandma's Pie Safe Side Frames: 3 1/4" to top edge of taper and bottom edge of rail I
97/99 Country Workshop 53 Grandma's Pie Safe Buying Guide: telephone area code changed to 570; hardware change to polished brass latch
1998 Outdoor Projects You Can Build 19 Patio Glider Buying guide: New address McFeely's, PO Box 11169, Lynchburg, VA 24506-9963 or call 800/443-7937
1998 Holiday Decorations & Gifts 29 Snowman Buying Guide address change: Roberts Studio, 2620 Heather Road, Seymour, TN 37865, 800/316-9010
1998 Outdoor Projects You Can Build 59, 65 Adirondack Rocker Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 64 and 65.
1999 Furniture You Can Build 8 Rolltop Writing Desk Note: Tambour kit in buying guide is no longer available
1999 Furniture You Can Build 10 Rolltop Writing Desk Add to Supplies: 1" brass knob (6) and 1 1/4" brass knob (2)
1999 Furniture You Can Build 15 Rolltop Writing Desk Buying Guide: Tambour and knobs no longer available
1999 Furniture You Can Build 15 Rolltop Writing Desk Taper Jig: new phone Constantines Wood Center 954/561-1716, www.constantines.com
1999 Furniture You Can Build 48 Capacious Country Cabinet Supplies: Stanley hinges are no longer available. See plan DP-00060 for updated project.
1999 Furniture You Can Build 54 Glass-Topped Table Buying guide is no longer available.
1999 Furniture You Can Build 64 Mission Dining Set Buying Guide: kit discontinued. Tabletop fasteners #34215, T-nuts #26054, and floor guides #18657 available from Rockler at 800/279-4441 or rockler.com; wooden table slides #51040 available from Classic Designs by Matthew Burak at 800/748-3480 or tablelegs.com; table aligners #JH 3 available from Woodworker's Hardware at 800/383-0130 or wwhardware.com
1999 Furniture You Can Build 69 Mission Chair (Dining Chair) Side Frame Assembly: Part D is 15 5/16" length
1999 Outdoor Projects You Can Build 18 Picnic Suite Cutting Core Block, Part C: change 3 1/4" width to 3"; 13/16" to 3/4", 1 5/8" to 1 1/2", 2 7/16" to 2 1/4"
1999 Outdoor Projects You Can Build 18 Picnic Suite Cutting Core Block, Tablesaw Fence: change 1 3/8" to 1 5/16", 2 3/4" to 2 5/8"
1999 Outdoor Projects You Can Build 19 Picnic Suite Table Exploded View: Part C, Core Block, 2 3/4" change to 2 5/8"
1999 Outdoor Projects You Can Build 19 Picnic Suite Materials List changes: 1 5/8" Thickness to 1 1/2"; Part C Thickness 2 5/8"; Part C Width to 3"; part C Laminated Redwood
1999 Outdoor Projects You Can Build 20 Picnic Suite Step 11: text change to cut the block to 2 5/8"x3"; set the fence 2 1/4" away from the base of the blade; then make the cut
2001 30+ Great Gifts 29 Timeless Timekeeper Buying Guide: Supplier for quartersawn oak no longer available.
2001 30+ Great Gifts 32 Wake-Up Call Buying Guide is no longer available, no other source
2001 30+ Great Gifts 56 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2001 30+ Great Gifts 76 Snowman Buying Guide, new address: Roberts Studio, 2620 Heather Road, Seymour, TN 37865, 800/316-9010
2001 Best-Ever Workshops 27 Universal wall cabinet system Exploded View: Change 3/4x2 inch non-mortise hinge to 7/8x2-1/2 inch non-mortise hinge
2001 Best-Ever Workshops 29 Universal wall cabinet system Buying Guide, hardware: Change brass pull to cat. no. 39768; change no-mortise hinge to 7/8x2-1/2 inch
2001 Best-Ever Workshops 66 Full-service workbench Buying Guide Vise: New address 1177 Rosemar Road, P.O. Box 1686, Parkersburg, WV 26102
2001 Best-Ever Workshops 79 Swivel-topped tool cabinet Step 8: use locking swivel and fixed casters
2001 Best-Ever Workshops 80 Swivel-topped tool cabinet Supplies: use 2–2 1/2" locking swivel casters
2001 Best-Ever Workshops 81 Swivel-topped tool cabinet Exploded View: 2 1/2" locking swivel caster
2001 Best-Ever Workshops 95 Wiring Your Shop A subpanel requires two separate bus bars, one for the ground wires and one for the neutral wires. The ground bus bar amounts directly to the panel box, and the neutral bus bar should rest on an insulating block to keep the neutral wires from contacting the panel box. Also, in a subpanel, the ground wire must come from the main service entrance panel to provide a "least resistance" ground path for any fault current. Remember, don't take chances with electricity. Always consult local codes and get the advice of a certified electrician before beginning any do-it-yourself electrical work.
2001 Great Outdoor Projects 12 Drive Screws that Hold Labels switched on photo: Phillips/square drive and Star (Torx) drive
2002 Storage Solutions 66-67 Bedroom Solutions (loft bed) Bill of Materials/illustration: Eliminate part E, make 2 part D corner posts
2002 101 Workshop Projects 18 Workbench Tool Crib End Detail: 3/8" hole should be 1 3/4" from edge
2002 101 Workshop Projects 25 Binder Drilling Jig Part D: 1/4" dia. Dowel pins not 3/8"
2002 101 Workshop Projects 27 Drafting/Reference Center Self-closing hinge should be 12" not 14". Available from: Wooworker's Hardware (#KV8080 PEZ12) 800/383-0130
Arrow for 1/4x3/4x15 1/2 maple goes to front edge of board for a band. New Buying Guide for 4-position multiuse bracket (3/03) is now Woodworker's Hardware (800/383-0130) #KV0206 ZC 12
2002 101 Workshop Projects 47 Depth Gauge Step 2: 7/64" holes through the brass (not 7/16")
2002 101 Workshop Projects 53 Masterful Marking Gauge Buying Guide parts are no longer available.
2002 101 Workshop Projects 62 Strip Sander Step 4: 7/64" pilot hole (not 7/16")
2002 101 Workshop Projects 80 Roll-Around Plywood Cart Side View, End Panel A: top, 3" should be 2 1/4"; angled side edge, first 18 3/4" should be 18 1/4"
2002 101 Workshop Projects 91 High & Mighty Tablesaw Jig Buying Guide should be: Schlabaugh & Sons Woodworking, 720 14th Street, Kalona, IA 52247, or call 800/346-9663
2002 101 Workshop Projects 97 Sliding-base taper jig Buying Guide Hardware Kit is no longer available.
2002 101 Workshop Projects 108 Pocket-Hole Routing Jig 15° stock should be 3/4x2 5/8x9 5/8"
2002 Best-Ever Workshops 27 Universal wall cabinet system Exploded View: Change 3/4x2 inch non-mortise hinge to 7/8x2-1/2 inch non-mortise hinge
2002 Best-Ever Workshops 29 Universal wall cabinet system Buying Guide, hardware: Change brass pull to cat. no. 39768; change no-mortise hinge to 7/8x2-1/2 inch
2002 Best-Ever Workshops 30 Forstner Bit Holders The photo is upside down
2002 Best-Ever Workshops 66 Full-service workbench Buying Guide Vise: New address 1177 Rosemar Road, P.O. Box 1686, Parkersburg, WV 26102
2002 Best-Ever Workshops 79 Swivel-topped tool cabinet Step 8: use locking swivel and fixed casters
2002 Best-Ever Workshops 80 Swivel-topped tool cabinet Supplies: use 2–2 1/2" locking swivel casters
2002 Best-Ever Workshops 81 Swivel-topped tool cabinet Exploded View: 2 1/2" locking swivel caster
2002 Great Outdoor Projects 39 Classic Adirondack Step 3: Clamp a fence to your drill-press table 1 7/16" not 17/16" from the center of the bit.
2002 Great Outdoor Projects 17 Patio Glider Buying guide: New address McFeely's, PO Box 11169, Lynchburg, VA 24506-9963 or call 800/443-7937
2003 Best-Ever Outdoor Projects 6 Adirondack Chair Step 3: Clamp a fence to your drill-press table 1 7/16" not 17/16" from the center of the bit.
2003 Best-Ever Outdoor Projects 25 Adirondack Rocker Note: Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 24 and 25.
2003

Best-Ever Outdoor Projects

28 Picnic Suite Table Exploded View: Part C, Core Block, 2 3/4" change to 2 5/8"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Cutting Core Block, Part C: change 3 1/4" width to 3"; 13/16" to 3/4", 1 5/8" to 1 1/2", 2 7/16" to 2 1/4"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Cutting the Core Block, Tablesaw Fence: change 1 3/8" to 1 5/16", 2 3/4" to 2 5/8"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Step 11: text change to cut the block to 2 5/8"x3"; set the fence 2 1/4" away from the base of the blade; then make the cut
2003 Best-Ever Outdoor Projects 31 Picnic Suite Materials List changes: 1 5/8" Thickness to 1 1/2"; Part C Thickness 2 5/8"; Part C Width to 3"; part C Laminated Redwood
2003 Best-Ever Outdoor Projects 91 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2003 Best-Ever Outdoor Projects 105 Sees & Such Snack Shop Change "However, birds that typcically feed on the ground, like cardinals and juncoes, use a crevice in a tree bark to hold their seed while they peck it open." to "However, cardinals and juncos use the platform board. Nuthatches wedge seed into a crevice to peck."
2003 Best-Ever Workshop Solutions 14 One workhorse of a workbench Buying Guide, Vise: Quick-release vise, no. 144844. Woodcraft, 800-225-1153, woodcraft.com. Bench dogs no longer available from Woodcraft. Use bench dogs of your choice.
2003 Best-Ever Workshop Solutions 21 Labor-of-Love Workbench Materials key: B-birch, BP-birch plywood
2003 Best-Ever Workshop Solutions 21 Labor-of-Love Workbench Buying Guide, Hardware: wood pulls are 3-7/8" not 4". Laminated maple benchtop, part no. BBT30060, Dunn & Company, 800-728-3866.
2003 Best-Ever Workshop Solutions 32, 35 Mobile mitersaw center Exploded View and Buying Guide: fixed casters no. 141053; swivel casters no. 141050; 3" wire pull no. 836159.
2003 Best-Ever Workshop Solutions 51 Tilt-top router table Drawing 8 Fence:Top view is Part Y not X. Front View is Part X not Y.
2003 Best-Ever Workshop Solutions 53 Tilt-top router table Materials List: Base is Part Y; Fence is Part X.
2003 Best-Ever Workshop Solutions 54 Full-service benchtop router table Use T-track instead of T-slotted mini tracks and mini track
2003 Best-Ever Workshop Solutions 55 Full-service benchtop router table Drawing 1: change mini-track to T-track; screws for T-track are #6x1/2 inch F.H. wood screws; change Round-knob to 3/4 inch stud not 1/2 inch stud
2003 Best-Ever Workshop Solutions 56 Full-service benchtop router table Step 5: change mini-track to T-track
2003 Best-Ever Workshop Solutions 57 Full-service benchtop router table Drawing 3: change mini-track to T-track; step 3 change mini-track to T-track
2003 Best-Ever Workshop Solutions 59 Full-service benchtop router table Step 2: change mini-track to T-track; Step 4 "See Buying Guide for our source of knobs."
2003 Best-Ever Workshop Solutions 59 Full-service benchtop router table Supplies: move 1/4 inch hexhead bolts from Buying Guide to Supplies list; add #6x1/2 inch F.H. wood screws. Updated Buying Guide: Hardware. Knobs with 1/4 inch threaded insert no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36 inch T-track no. 12K79.24 (1); 24 inch T-track no. 12K79.22 (2); 2-1/2 inch vac port no. 03J61.10 (1). Lee Valley, 800-871-8158, leevalley.com. Switch: Safety power switch no. 20915. Rockler, 800-279-4441, rockler.com
2003 Best-Ever Workshop Solutions 66 Router retrofit Buying Guide, router plate. Insert plate, 3/8x12x12" acrylic no. 16L71. Woodcraft, 800-225-1153, woodcraft.com
2003 Best-Ever Workshop Solutions 88 Tablesaw accessories cabinet Buying Guide, hardware. 3" wire pulls no. 836159.
2003 Best-Ever Workshop Solutions 110 Drill-press table Buying Guide. Ready-to-assemble kit no longer available.
2003 Best-Ever Furniture You Can Build 69 The Entertainer Supplies: Stanley hinges are no longer available. See plan DP-00060 for updated project.
2003 Best-Ever Furniture You Can Build 84 Shelving Showcase Section View: 1/4" flutes 3/16" deep
2003 Best-Ever Furniture You Can Build 87 Shelving Showcase Drawing 8b should be 8a
2004 Best-Ever Outdoor Projects 111 Grand entrance (gate) Drawing 6 and Step 4, Part R: Lay part R diagonally across the assembly with the top end opposite the hinge side.
2004 Best-Ever Outdoor Projects 113 Grand entrance (gate) Buying Guide: HardieSingle Individual Shingles, web site www.jameshardie.com
2004 Best-Ever Workshop Tips, Jigs and Organizers 22 Bandsaw Fence 3/8" all-thread rod 1" longer than A not 26 3/8" long
2004 Best-Ever Workshop Tips, Jigs and Organizers 41 Dovetail-Jig Stabilizer Fixture Porter-Cable model 5008 Dovetail Templet is no longer available.
2004 Best-Ever Workshop Tips, Jigs and Organizers 97 Rout parallel slots to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2004 101 Workshop Projects 53 Masterful Marking Gauge Buying Guide parts are no longer available.
2004 101 Workshop Projects 97 Sliding-base taper jig Buying Guide Hardware Kit is no longer available.
2005 450+ Best-Ever Shop Tips 21 One-handed bar clamp keeps crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2005 Best-Ever Outdoor Projects 12 Drive Screws that Hold Labels switched on photo: Phillips/square drive and Star (Torx) drive
2005 Best-Ever Outdoor Projects 128 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2005 Best-Ever Workshops 77 Tough-Stuff Workbench Update Sources, Cabinets: Can also use 28" full-extension drawer slides no. 02K30.28
2005 Best-Ever Workshop Solutions 14 One workhorse of a workbench Buying Guide: Bench dogs no longer available from Woodcraft. Use bench dogs of your choice.
2005 Best-Ever Workshop Solutions 21 Labor of love workbench Buying Guide, Hardware: wood pulls are 3-7/8" not 4". Laminated maple benchtop, part no. BBT30060, Dunn & Company, 800-728-3866.
2005 Best-Ever Workshop Solutions 32, 35 Mobile mitersaw center Buying Guide, Hardware: 3" wire pull no. 836159.
2005 Best-Ever Workshop Solutions 51 Tilt-top router table Drawing 8 Fence: Top view is Part Y not X. Front view is Part X not Y.
2005 Best-Ever Workshop Solutions 53 Tilt-top router table Materials List: Base is Part Y; Fence is Part X.
2005 Best-Ever Workshop Solutions 54 Full-service benchtop router table Use T-track instead of T-slotted mini tracks and mini track
2005 Best-Ever Workshop Solutions 55 Full-service benchtop router table Drawing 1: change mini-track to T-track; screws for T-track are #6x1/2 inch F.H. wood screws; change Round-knob to 3/4 inch stud not 1/2 inch stud
2005 Best-Ever Workshop Solutions 56 Full-service benchtop router table Step 5: change mini-track to T-track
2005 Best-Ever Workshop Solutions 57 Full-service benchtop router table Drawing 3: change mini-track to T-track; step 3 change mini-track to T-track
2005 Best-Ever Workshop Solutions 59 Full-service benchtop router table Step 2: change mini-track to T-track; Step 4 "See Buying Guide for our source of knobs."
2005 Best-Ever Workshop Solutions 59 Full-service benchtop router table Supplies: move 1/4 inch hexhead bolts from Buying Guide to Supplies list; add #6x1/2 inch F.H. wood screws. Updated Buying Guide: Hardware. Knobs with 1/4 inch threaded insert no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36 inch T-track no. 12K79.24 (1); 24 inch T-track no. 12K79.22 (2); 2-1/2 inch vac port no. 03J61.10 (1). Lee Valley, 800-871-8158, leevalley.com. Switch: Safety power switch no. 20915. Rockler, 800-279-4441, rockler.com
2005 Best-Ever Workshop Solutions 65, 66 Router retrofit Buying Guide, Router plate. Insert plate, 3/8x12x12" acrylic no. 16L71. Woodcraft, 800-225-1153, woodcraft.com
2005 Best-Ever Workshop Solutions 88 Tablesaw accessories cabinet Buying Guide, Hardware. 3 inch wire pulls (2) no. 836159. Woodcraft.
2005 Best-Ever Workshop Solutions 110 Drill-press table Buying Guide, Ready-to-assemble kit is no longer available.
2005 450+ Best-Ever Shop Tips 13 Super-Simple Taper Jig Buying Guide Hardware Kit is no longer available.
2006 Great Outdoor Projects 66 Down-to-earth bench Buying Guide: Foam Kneeling Pads. Part no. changed to KP816. Sold in single pack.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
9 Weather station Source, instruments: Kit is no longer available.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
33 Occasional table Scrapwood router trammel: Reverse arrow on routing direction towards top of the circle
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
47 Treasured chest Drawing 1b is missing: Part M notch is 3/8 by 3/8 inches
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
56 Kid's room ensemble Cork source is no longer available. Cork: Art and craft supply stores. Adhesive: 3M Super77 Multi-Purpose Adhesive, hardware stores and home centers.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
73 Pendulum Cradle Drawing 2: Measurement 9-5/8" should be 10-1/8"; 3-1/8" should be 2-1/4"; 13" should be 13-3/8"
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
77 Pendulum Cradle Sources, Cradle Pad: 17x31" vinyl-covered foam pad, No. A002112. Call Ababy.com at 877-552-2229 or go to ababy.com
2006 Best-Ever Home Shop Ideas 10 Bright ideas Lights Now product is no longer available.
2006 Best-Ever Home Shop Ideas 26-27 Guide to base and wall units for our garage California Closets phone 800/274-6754;
osullivan-furniture-online.com phone 866/914-4204;
Garage Tek phone 866/664-2724; Garage Storage Cabinets website garagestoragecabinets.com;
Lista website listacabinets.com; Mitchell Cabinets by IST now Cooper Cabinet Systems, available in variety of sizes, coopercabinetsystems.com
2006 Best-Ever Home Shop Ideas 10 Bright ideas Lights Now product is no longer available.
2006 Best-Ever Home Shop Ideas 59 Super-flexible shop storage Hardware update: plastic sliding door track, no. 10007, shelf pins, no. 22773, available from Rockler, rockler.com. 800-279-4441
2006 Best-Ever Home Shop Ideas 72 Mobile sanding center Buying Guides of vacuum and dust-collection system are no longer available
2006 Best-Ever Home Shop Ideas 77 Tough-stuff workbench Sources, cabinet: full-extension drawer slides part no. 02K30.28
2006 Best-Ever Home Shop Ideas 77 Tough-stuff workbench Plans for workshop Stool are no longer available.
2006 Best-Ever Home Shop Ideas 90 3-in-1 Work Support Source, hardware, update: aluminum mini-track available from Rockler, rockler.com, 800-279-4441, part no. 34676
2006 Best-Ever Home Shop Ideas 101 Super-flexible shop storage Hardware update: plastic sliding door track, no. 10007, shelf pins, no. 22773, available from Rockler, rockler.com. 800-279-4441
2006 Best-Ever Home Shop Ideas 115 Whole-shop air-cleaning system Buying guide, blower/motor: Grainger changed the motor to stock no. 7D554, 1,280-1,587 cfm, new phone no. 888-361-8649 Note: The blower cabinet and filter cabinet are based on the particular model we used. Measure your blower and filter before beginning construction to make sure they will fit in the cabinets dimensioned here. Cabinet sizes may need to be adjusted for other models of blowers and filters.
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 11 Dead-on 90 degree crosscut sled Drawing 1: guide bar change to 3/8x1/2x1-1/4 inch; Stopblock change to 3/8 inch dado 1/4 inch deep 7/8 inch from top edge; washer is 1/4 inch flat washer
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 78 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 79 Mitersaw work station Drawing 2, BASE and Materials List: J is 14-3/4 inches not 14 inches; Key 3-1/2 inches is 3-1/4 inches.
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 81 Wall Cabinet Drawing 4: Shelf holes start 7" inches from top not 7-1/4 inches from top of part A.
2007 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 81 Enlarge a hole of almost any shape Illustration, Step 2: Arrow showing bit direction should be pointing to the left
2007 215 Fixes for Common Woodworking Mistakes 12 Fix 22 Photo labels should be: Loose hook: 12-13/16; Tight hook: 12-3/4 and move pencil mark to 12-3/4
2007 215 Fixes for Common Woodworking Mistakes 26 Fix 42 Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2007 215 Fixes for Common Woodworking Mistakes 56 Fix 92 How Climb-Cutting Give Smoother Results: Shape of bit should be round not oval
2007 215 Fixes for Common Woodworking Mistakes 68 Fix 103 Drawing 1, Box-Joint Sled: The width of the blade guard and acrylic on the box-joint sled is 3-1/4" wide to allow for the rotating of the four-arm knobs. The adjusted slot length is 3/4" and location is 3-3/8" from outside edge of fence.
2007 Best-Ever Decks & Backyard Projects 103 Grand entrance (gate) Drawing 6 and Step 4, Part R: Lay part R diagonally across the assembly with the top end opposite the hinge side.
2007 Best-Ever Decks & Backyard Projects 105 Grand entrance (gate) Buying Guide: HardieSingle Individual Shingles, web site www.jameshardie.com
2007 America's Best Home Workshops 144-145 Guide to base and wall units for our garage California Closets phone 800/274-6754;
osullivan-furniture-online.com phone 866/914-4204;
Garage Storage Cabinets website garagestoragecabinets.com;
Lista phone 888/897-9050, website listacabinets.com;
Mitchell Cabinets by IST now Cooper Cabinet Systems, available in variety of sizes
2007 Best-Ever Workshop Jigs, Tips, and Ideas 42 Rour parallel slots to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2007 Best-Ever Workshop Jigs, Tips, and Ideas 76 Wider is Better for Resaw Feather Boards The feather-board fingers apply pressure to workpiece only in front of the blade.
2007 Best-Ever Workshop Jigs, Tips, and Ideas 125 Steady-as-She-Goes Biscuit Joiner Jig Handhold: 1 inchradius not 2 inch radius; 3/4 inch radius not 1-1/2 inch radius
2007 450+ Best-Ever Shop Tips 13 Super-Simple Taper Jig Buying Guide Hardware Kit is no longer available.
2007 450+ Best-Ever Shop Tips 21 One-handed bar clamp keeps crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2007 450+ Best-Ever Shop Tips 22 Clean-cut lids for closed boxes Missing copy at end of tip: the glue before sanding to remove the saw marks. -John Ash, Lockport, Ill.
2008 Best-Ever Router Tips, Tricks & Jigs 82 Full-service bench-top router table Source, hardware: Knobs no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36" T-track no. 12K79.24; 24" T-track no. 12K79.22; 2-1/2" vac port no. 03J61.10. Lee Valley, 800-871-8158, leevalley.com. Safety power tool switch no. 20915. Rockler, 800-279-4441.
2008 Best-Ever Router Tips, Tricks & Jigs 113 Rout parallel sltos to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2008 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 11 Dead-on 90 degree crosscut sled Drawing 1: guide bar change to 3/8x1/2x1-1/4 inch; Stopblock change to 3/8 inch dado 1/4 inch deep 7/8 inch from top edge; washer is 1/4 inch flat washer
2008 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 78 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2008 America's Best Home Workshops 112 Drill-Press/Mortiser Stand Delta 50-322 Planer Stand from toolmarts.com
2009 Best-Ever Home Shop Ideas 25 Workshop Cabinetry Gladiator Web address is: gladiatorw.com
2009 Best-Ever Home Shop Ideas 28 Get Wired A subpanel requires two separate bus bars, one for the ground wires and one for the neutral wires. The ground bus bar amounts directly to the panel box, and the neutral bus bar should rest on an insulating block to keep the neutral wires from contacting the panel box. Also, in a subpanel, the ground wire must come from the main service entrance panel to provide a "least resistance" ground path for any fault current. Remember, don't take chances with electricity. Always consult local codes and get the advice of a certified electrician before beginning any do-it-yourself electrical work.
2009 Best-Ever Home Shop Ideas 46 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2009 Best-Ever Home Shop Ideas 61 Bench-tool System Project Highlights, item 4: Locking casters not dual-locking casters
2009 Best-Ever Home Shop Ideas 63 Bench-tool System Drawing 4: Locking swivel casters not dual-locking swivel caster
2009 Best-Ever Home Shop Ideas 64 Bench-tool System Drawing 5: 4" locking swivel caster not dual-locking swivel caster; Source: Casters, 4" locking swivel plate casters no 00K21.41. Lee Valley Tools, leevalley.com, 800-871-8158.
2009 Best-Ever Home Shop Ideas 77 Tablesaw Workbench Source: Casters no. 00K21.41, Lee Valley Tools, leevalley.com, 800-871-8158
2009 Best-Ever Home Shop Ideas 78 Tablesaw Workbench Drawing 2: locking swivel caster not double-locking swivel caster
2009 Best-Ever Outdoor Projects 23 Cozy rocker Full-size patterns for Cozy Rocker are no longer available.
2009 Best-Ever Outdoor Projects 81 Full-size patterns for the projects in this magazine Full-size patterns for Adirondack Lawn Rocker Plan OFS-1016 are no longer available.
2009 101+ Best-Ever Workshop Projects 51 Versa-Cab Drawing, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 65 Tablesaw Workbench Source: Casters no. 00K21.41, Lee Valley Tools, leevalley.com, 800-871-8158s
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 66 Tablesaw Workbench Drawing 2: locking swivel caster not double-locking swivel caster
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 124 Bar clamp helps keep crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2010 Best-Ever Storage Solutions 21 The Shelf Maker's Complete Guide Adjustable support options: Low-profile shelf standard is shown in photo but not labeled, used with low-profile support labeled as before and after insertion.
2010 Best-Ever Storage Solutions 76 Closet Storage Supplies: See items in Source, page 80 not 94.
2010 Best-Ever Workshop Jigs, Tips, and Ideas 109 Steady-as-She-Goes Biscuit Joiner Jig Handhold: 1 inchradius not 2 inch radius; 3/4 inch radius not 1-1/2 inch radius
2011 America's Best Home Workshops 106 Drill-Press/Mortiser Stand Delta 50-322 Planer Stand from toolmarts.com
2011 Great Garage Makeovers 16 dream garage on the prairie There is a layer of drywall sandwiched between the MDF and 2x6 (not shown in Section View and Exploded View)
2011 Great Garage Makeovers 74-75 safe, solid, and secure Model number updates: Stanley Tool Works new model FMST20061; Craftsman new model 31017 and model 31016
2011 Great Garage Makeovers 93 Gallery of Garage Art Web site for "Check the Oil!" is checktheoilmagazine.com
2011 101 Best-Ever Workshop Projects 36 Mitered half-lap joinery jig twosome Build the mitered half-lap jig using the width of your frame as the length of fence reach beyond the base.
2011 101 Best-Ever Workshop Projects 98 Pocket-hole jig organizer and base Organizer was designed to fit a Kreg K3 jig. You may need to adapt the dimensions and workpiece support height to suit your jig.
2011 101 Best-Ever Project and Shop Tips 56-60 Shaker Clock Source: Clock kit: Radio-controlled clock movement no longer available. Replaced with quartz clock movement. Order kit no. SK-WAL-Q for walnut or kit no. SK-CH-Q for cherry.

 

close


Comments (20)
8341591352
scorpio_aq wrote:

Issue 222 November 2013 On the Easy to Build Country Sideboard: Part "D" the high must be 20 3/4 instead of 20 1/2, Part "A" the distance from the top to the first dado must be 11 1/2, this avoid the uneven finish between "B" and "K".

11/10/2013 01:18:56 PM Report Abuse
kjarrett65 wrote:

Didn't see an answer to this particular problem, so I will assume it does not exist. On several of your plans it calls for inserting a 3/4" diameter pipe into a 3/4" diameter hole. the problem arises in that pipe is figured based on the "inside" diameter instead of the outside. In this situation a 3/4" diameter pipe would require a hole diameter of at least 1 1/16" Thank you, Rev. Keith Jarrett

7/15/2013 08:29:45 PM Report Abuse
kathleensmit wrote:

Issue 219 - July 2013 Raised-panel-bit boxes. Pages 54 and 55 are not complete. Need to be reprinted.

5/23/2013 05:05:03 PM Report Abuse
swallace19431 wrote:

Issue # 218 (May 2013). In the text, para.2, you say, position the rip fence 31/4 inch from the dado blade. However in the illistration, pg. 47 it shows the dado 3 inches in from the end of the board. Which is correct?

5/14/2013 04:42:37 PM Report Abuse
charles hachat wrote:

issue 215 dump truck,location of wheel holes can't be correct.rear dual wheel hole 1 5/8 and 2 1/8 too close.approximately 3 3/4 from end on second hole.

5/8/2013 02:04:25 PM Report Abuse
dickcottrell47 wrote:

I have a June of 1994 Wood Magazine that has an article on 44 regarding building a solar "Kiln" The article offers plans and material list to build the kiln for $9.95. I sent a check and request for plans and material list to the address at wood magazine and my letter came back "undeliverable". Who do I send this to.....? to get a set of plans and material list? dick cottrell

4/3/2013 10:58:24 AM Report Abuse
jerry h. wrote:

Iss. 218,page43,drawing 2,should the rabbets be 1/4/in instead of 3/8?

3/16/2013 09:17:50 PM Report Abuse
Cyberwil2 wrote:

Looking a the Dec/Jan 2012/2013 issue and on page 18 is a Dead-on accurate Shelf-pin jig. The story says to use the drawing at the right to build the jig. No drawing.

2/18/2013 07:59:32 PM Report Abuse
drury.william wrote:

i am looking april 1989 issue page 70 issue 28 it's a acorn bird

12/18/2012 09:56:31 AM Report Abuse
rgross241 wrote:

In Issue 208 the material list does not list part "A" nor any sizes for this part

11/25/2012 02:37:07 PM Report Abuse
bob_trowbridge wrote:

Issue 209 - Box Joint jig I am new a routing. My router will only extend above the table 15/16", with a 1/4" mounting plate. If I use a 3/4" bedplate on the jig, the bit will only extend 3/16" above the plate. I have a 5/16" dia. bit, so the extension needs to be 5/16". Are there longer bits available? Or does my Craftsman router have too short a travel? I am into woodworking on a shoestring budget.

10/21/2012 10:27:20 AM Report Abuse
grzendafarm1 wrote:

Nov 2012 issue: On Page 62, the web site for the hardware kit is correct but they do not offer that kit. Any suggestions as to another site?

10/16/2012 07:40:12 AM Report Abuse
MadMaxH3 wrote:

In issue #213 on page 60 for the "Tic-Tac-Toe Game Set", should the dimensions for "Part D - top/bottom panels" be : 1/4"x 4-5/8"x4-5/8" ?

8/8/2012 07:15:40 PM Report Abuse
sshanman wrote:

I am currently working on the Playtime Express found in Issue #14, page #74 and have a question regarding part "U" the top of the passenger car. The plan calls out a 1/2" beading bit. The part is listed as 1/2" stock. This bit is too large to leave a reveal top and bottom as shown in the photo. Is it supposed to be a 3/8" or 5/16" bit?. If you center a 3/8" bit the piece wants to crawl under the bearing. Thank you, Sam Shanman. samuelshanman824@gmail.com

4/21/2012 08:50:36 PM Report Abuse
vernshomes2 wrote:

In issue #209 dec/jan 2011/2012 The carousel music box I made but unite was to unstable that I put a ring lazy suzan in it and made a world of difference on how it looks and works Vernon Johnson Clearwater MN 55320 612 202 5708 VernsHomes@ gmail.com

2/18/2012 12:38:01 PM Report Abuse
lgreen512 wrote:

Thanks for a great project this month(Mar 12)and thanks for the update, but I think there is another misprint. Part "F" how far up or down due you drill the holes(3/8")from the end. You say find the center point and drill 3/8" holes even on the drawinds you do not have the measerments like everything else. Your help is needed-----Thanks

2/16/2012 10:57:13 PM Report Abuse
greyowl8 wrote:

Iżve subscribed to Wood magazine almost from the beginning. How about posting these changes / updates in a downloadable searchable PDF, excel or some such file.

1/1/2012 02:20:39 PM Report Abuse
Rich J. wrote:

I would like to build the crownless shelf from issue197 May/ June 2010, but I am having no luck finding the plyood cap moulding in oak. Anyone have a thought where I might be able to locate this.

7/24/2011 09:49:15 AM Report Abuse
steel_dragon67 wrote:

@ronnmeg you can find assorted candies at your local Cracker Barrel or you can go to Gumball.com hope this helps

1/25/2011 06:59:41 PM Report Abuse
m_saffel wrote:

issue 202 gumball machine, I found that if you put round hard candy instead of gumballs works just as well.

12/29/2010 02:24:06 PM Report Abuse

Add your comment

You must be logged in to leave a comment. Register | Log In

Please confirm your comment by answering the question below and clicking "Submit Comment."

 

 
 
Connect With Us
  • Recent Posts
  • Top Posts
See More >