Magazine Changes and Updates
SPECIAL OFFER: - Limited Time Only!
(The ad below will not display on your printed page)

Wood Magazine

Magazine Changes and Updates

Issues 1 - 50
WOOD MAGAZINE CHANGES / UPDATES Issue 1-50
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
1 October 1984 49 Cutting board Cutting diagram: Part B 24" long
1 October 1984 75 Bracelet Mandrel is 2-1/4" diameter down to 1-1/2" diameter
2 December 1984 54 Walnut and maple frame Bill of Materials: parts order C, D, A, B
5 June 1985 57 Pint-sized picnic table DO NOT USE--SEE Outdoor Projects 1994 for correct drawings and dimensions, page 62.
6 August 1985 34 Workbench Building and installing the vise: Step 1 "Laminate two pieces of 1 1/2"-thick pine to form the vise jaw (N)."
7 October 1985 50 Surface sander Cutting Diagram: 3/4x26x48" Fir Plywood
7 October 1985 81 Oak coffee table Laying Out The Pin, Part C: 15/16" should be 1 5/16"
8 December 1985 35 Woodworker's mallets Drawing (top, left) 2 15/16" should be 1 15/16"
9 February 1986 69 Dining Table Article continued on page 87
10 April 1986 42 Solid oak dining chair Cutting Diagram: Cut part E from 1 1/16" stock or laminate two pieces of 3/4" stock
10 April 1986 42 Solid oak dining chair Assembly: Part C 16 1/8" = shoulder length equals 14 1/2" plus tenon of 7/16" and tenon of 1 3/16"
10 April 1986 60 Redwood Lantern Part F: top 4-1/8" not 5-1/8"; side 2-1/2" not 3"; 52° not 53°
12 August 1986 68 Oak breakfast tray Cutting The Box Joints, Step 1: B = 3 13/16"x12"
13 October 1986 47 Heirloom cedar chest Front Frame, Part A: tenon 1" not 1 1/2"
13 October 1986 48 Heirloom cedar chest Side Section, bottom, right: 3" and 2 1/2" transposed
13 October 1986 49 Heirloom cedar chest Supplies: 1 1/2 x 2 1/2" brass butt hinge not 1/2 x 2 1/2"
13 October 1986 51 Heirloom cedar chest Buying Guide updates: Router bit available from Sears, Craftsman 26330; Counterbalanced lid support available from Rockler, no. 26179, 800/279-4441 or rockler.com
13 October 1986 71 Jewelry Case Buying Guide: Source of Craftsman Wood Service is no longer available. Hinges available through VanDyke's Restoration part #AL02265564. Also Ace or TruValue Hardware stores under Brainerd #9054.
14 December 1986 49 Folk toys Flap Jack: 3 7/8" from center of hole to bottom of upright
14 December 1986 50 Folk toys See Saw: Arms 1/8x3/8x1 7/8"
14 December 1986 67, 69 Oak magazine rack Part F: Lap joints 3/16" deep
15 February 1987 68 Quilt Rack Project revised - see WOOD PLAN IFS-1004
16 April 1987  43 Sander Cabinet Bill of Materials: Part A width 13 1/4"; Part D length 13 1/4"; Part L length 13 1/4"
16 April 1987 49 Aniline Dyes Updated sources: Constantines Wood Center, 954/561-1716; Highland Hardware, 800/241-6748; Lee Valley Tools Ltd., 800/871-8158; Woodcraft Supply Corp., 800/225-1153
16 April 1987 63 Homemade lathe Bed Assembly: missing dimension on Pedestal is 1 1/2"; Pedestal missing dimension on part F 14"
16 April 1987 64 Homemade lathe Motor Mount: Part K from hole to edge 1 1/2" not 1/2"
16 April 1987 65 Homemade lathe Headstock Spindle: length 12 1/2" not 11 1/2"
16 April 1987 68 Homemade lathe Power Switch source: AMT
17 June 1987 38 Pin Routing Attachment Note: fits router tabletop measuring 24x16"
17 June 1987 71 Settee Bill of Materials, part B, 23 1/4" not 23 3/4"
18 August 1987 20 Tips From Your Shop (and ours) Quick 'N' Easy Band Saw Extension Table: The blade kerf for the bandsaw extension table can be made as shown, by cutting a kerf in from the left-hand side of the plywood table slightly wider than the blade. Or, an easier way to do this would be to slide the wood table through the blade, leaving a kerf behind the blade in the clamped-down extension table.
18 August 1987 41 Burl-topped coffee table Mortises: 5/8" from top of mortise to shoulder should be 1"
19 October 1987 14 Saw blade holder (tip) 2x6 delete
19 October 1987 58 Cradle Update Buying Guide: foam pad no longer available from Sears, contact Sleepland, at 3707 E. Hubbell Ave., Des Moines, IA 50317 or phone 515/262-2705.
19 October 1987 59 Cradle End Panel: 13" should be 13 3/8"; 2 3/8" should be 2 1/4"; 10 3/8" should be 10 1/8"
19 October 1987 62 Cradle Stand Shape is Support Upright Shape: top Part I is 7/8" from edge not 3/4"
19 October 1987 74 Bird feeder Gable Roof Support: 1" should be 1 9/16"
19 October 1987 75 Bird feeder Finishing Up, step 3: 1 1/4" pipe not 1 3/4" pipe; illustration 1 1/4" pipe; Bill of Materials 1 1/4" pipe and 1 1/4" flange
20 December 1987 65 Showcase wine rack Bill of Materials: Part E width 2 3/16"; illustration Part B 1/2" hole 5/8" from inside edge
20 December 1987 66 Showcase wine rack Stemware Supports: Part E holes 5/8" from edges; 8 1/2" from center of each hole; Part F hole 5/8" in from side edge. Cross Members, Part D, hole measurements (from center of holes) rear: 7/8" from both ends other holes 2 5/32" from center to next hole. Cross Members, Part D, hole measurements (from center of holes) front: 7/8" from both ends other holes 4 5/16" from center to next hole.
20 December 1987 79 Fat cat bulldozer Attach the Dozer Blade, Step 2, 56° note: If your miter gauge reads 0° when set perpendicular to the blade, set the gauge at 34°. If your miter gauge reads 90° when set perpendicular to the blade, set the gauge at 56°.
21 February 1988 50 Portrait Perfect Picture Frame Rabbet should be at least 1/4" deeper than picture package (glass, mat, mounting board, backing board)
21 February 1988 68 Barrister's bookcase See Talking Back Issue 23, June 1988, page 10, 1 1/2" should be 1 9/16"
21 February 1988 73 Stackable file cabinet Bill of Materials: Part F, width 1 5/8"; Part H, quantity 2
24 August 1988 35 Tractor Bill of Materials: Part D, length, 4 1/4"
25 October 1988 78 Mini-safe Bill of Materials: Part A, length, 5 1/2"; Part C, length, 4 15/16"
25 October 1988 79 Bill box and key keeper Bill of Materials: Part B, length, 10"
26 December 1988 68 Scrollsawn ornaments Illustration: 2 3/4" should be 1 3/8"
28 April 1989 20 More helpful tips First tip page 66 not page 42
28 April 1989 34 Southwest Bowl Block Pattern Lamination: Top layer 3 1/8" should be 3"
28 April 1989 35 Southwest Bowl Feature Layer: 6 1/4" should be 6", side dimensions add up to 12 3/8"
28 April 1989 49 Trestle table Illustration, right side: 3/16" hole countersunk on bottom side of (C) (not D); illustration, bottom center: End of (D) (not C) protrudes 1/2" from outside edge of (A) on both ends.
28 April 1989 51 Trestle table Support drawing: 3/8" should be 3 1/8"
28 April 1989 70 Acorn birdhouse Template, left side, to hole center: 3/4" should be 2"
29 June 1989 20 More tips Last tip page 70 not page 60
29 June 1989 46 Entertainment center Cutting diagram: material for Part A is Oak Plywood
29 June 1989 47 Entertainment center Cutting diagram: material for Parts M,N,O is 1/2x5 1/2x96" Oak
29 June 1989 81 Napkin holder center column, step 7, 3/4" hole in each shaker
29 June 1989 92 Entertainment center Buying Guide: new phone number 612/478-8201
30 August 1989 39 Shaker chair Dowel Clamp: letters clockwise are C/E/A/D/B
30 August 1989 43 Shaker chair Drilling Guide Chart: Right Front Leg change B to D; Left Front Leg change C to E
30 August 1989 61 Doll Cradle Edge-Join, Step 1: two 6 1/4x12" panels
30 August 1989 62 Doll Cradle Bill of Materials: Parts E and F 6 1/4" width
31 October 1989 32 Products That Perform Plantation Woodstains is out of business
31 October 1989 73 Classic Woody Cutting the tires, step 2: R = 21/32"
31 October 1989 77 Classic Woody License Plate is no longer available; instant glue is Hot Stuff Package, #21J06.10; hardwood source is out of date.
31 October 1989 77 Classic Woody Update (9/01): six spoked-wheel inserts available from Drico Products 888/577-3257
32 December 1989 46 Tambour desk Add to Supplies: 1" brass knob (6) and 1 1/4" brass knob (2)
32 December 1989 46 Tambour desk Bill of Materials: Part X Shelf, 3/4x5 1/2x41 1/2", material A, quantity 1
32 December 1989 51 Writing desk Buying Guide: Constantines no longer carries the porcelain knobs
Taper Jig: new phone, Constantines Wood Center, 954/561-1716, www.constantines.com
32 December 1989 86 Tabletop easel Bill of Materials: part B, 5/8" thick
32 December 1989 87 Tabletop easel Full-size hinge pattern - see correct pattern issue 34, page 14
33 February 1990 44 Oak dry sink Drawer: Cut a 7/8" rabbet 1/2" deep across both ends on the back surface of the drawer front
33 February 1990 45 Buying guide phone number 800/241-9741
34 April 1990 47 Dollhouse in a box Illustration chimney: 1/4" hole in chimney cap M
34 April 1990 73 Psaltery Buying Guide: 50 feed of #1 music wire
35 June 1990 62 Settee Seat Frame: #10x1 1/2" F.H. wood screws through E and into B; #10x1 1/2" F.H. screws into D and C
35 June 1990 65 Settee Braces (Q) pattern: Screw hole centerline not centerpoints
35 June 1990 69 Showcase Illustration part B: missing dimension for line 13 1/2"
35 June 1990 70 Showcase Spline Jig: side measurement is 4" not 2 1/2"
35 June 1990 75 Handscrew Clamps No Buying Guide Source (Jan 2003)
36 August 1990 45 Country clock You're almost done, step 1: dial backing C not D
37 September 1990 28 Worldwide Woods phone changed 303/425-7070
37 September 1990 53 Labor-of-Love Workbench Hole Locations Detail: part L label should be Q; part M label should be R; Buying Guide: Vise catalog no. G9850, Grizzly 800-523-4777; Laminate maple benchtop no. BBT30060, Dunn & Company, 800-728-3866, 1335 NE 50th Ave, Des Moines, IA 50313.
38 October 1990 22-23 Shop Tip Missing copy: "…stripping agent and that will speed the aging process of your new parts. About the third time you do this, you won't be able to distinguish the new part from the old ones."
39 December 1990 37 Castle caption: part P not part H
39 December 1990 41 Business-card case Bill of Materials: part E, width 3/8"
39 December 1990 46 Cutting board End Grain Detail: 1" between crosscuts not 3/4"
39 December 1990 72 Battling Harmful Vapors See Talking Back, June 1991, page 8, for safety update
40 January 1991 38 Large-Scale Moldings See Talking Back, August 1991, page 6, for formula for 8 and 9" blades.
40 January 1991 48 Sharpshooter's showcase Dentil mold detail: 3/8" dado 3/8" deep not 1/4"
40 January 1991 51 Sharpshooter's showcase Buying Guide sources are no longer available
41 February 1991 19 Chisel Rack Tip in Talking Back issue 51, April 1992, p. 10.
41 February 1991 51 Martin Guitar see pages xx is pages 52 and 53
41 February 1991 76 Cherry wall cabinet 1/2" rabbet 3/8" deep on both ends of part I (see step 3). Buying guide update: no-mortise hinge (#00H51.21) available from Lee Valley at leevalley.com. Cabinet kit no. 101WD is no longer available, order parts separately. Cherry Tree no longer selling cherry dowels, check your local hardware stores.
42 April 1991 59 Mahogany outdoor chair Cutting diagram: 3/4x9 1/4x96" Mahogany change bottom row to all part I
43 June 1991 14 Shop Tip (dust-collector switch) See Talking Back, February 1992, p. 6
43 June 1991 45 Dust Collection Buying Guide: Low-voltage switching kit. Double-pole, single-throw relay source: Grainger, part #4E944
43 June 1991 46 Dust collector Step 3: Cut a piece of 1/4" stock to 1 3/16" wide by 22" long for the louver supports (E).
43 June 1991 59 Duck under glass Step 4: crosscut two pieces of 3/8" stock to 1 1/2x24"
43 June 1991 81 Jelly bean machine Bill of Materials: Part E length 2 3/4"
44 August 1991 35 Calendar/Clock Buying Guide changed: New Products, 1 Alpine Court, Chestnut Ridge, NY 10927
44 August 1991 68 Home Brews Milk Paint see Talking Back issue 51, April 1992, p. 8
45 September 1991 50 Barstools Leg and Top Side Rail: measurements for breakfast barstool, top two mortise centerpoints 6" not 5 3/4", bottom 5 3/8"
46 October 1991 15 Palm-sander holder 1 1/2" stock (we used a 2x8 not 2x6)
46 October 1991 48 Work with Plywood Stop Block 3/8" hole, 1/4" deep. See Talking Back, issue 49, Jan 1992, p. 6
49 January 1992 31 Hand-Carved Cookie Molds Clarity: The 1 1/4" dimension refers to the distance between the two patterns. See Talking Back, issue 57, December 1992, page 12, for revised drawing.
49 January 1992 51 Acrylic-Impregnated Wood Clock/Pen set parts: Klockit, PO Box 636, Lake Geneva, WI 53147
49 January 1992 70 Shaker wall clock Buying Guide changed: Turncraft Clocks, Inc., PO Box 100, Mound, MN 55364-0100
50 February 1992 39 Shelving Showcase Vein Detail: 1/4" veins 3/16" deep
50 February 1992 58 Mitersaw Cabinet End View Detail: 17/32" groove not 1/4" groove for tape measure
50 February 1992 68 Rough ‘N' Ready Wrecker Bill of Materials: Part D 4 1/4" Length

 

Issues 51 - 100
WOOD MAGAZINE CHANGES / UPDATES Issues 51-100
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
51 April 1992 51 Dovetail Jig Locating The Guides: kerf should be on the right side, not left side. See Talking Back issue 54, September 1992, p. 8.
51 April 1992 58 High Chair Step 8: "With the outside face up" not down
51 April 1992 59 High Chair Miter-Cutting the Stretchers not Rails; Inside face up or Outside face down (part D); Bill of Materials: Part A 23 1/4" Length; Leg Assembly: A = 23 1/4" length; 3/16" shank hole not 5/32"; 1/8" pilot hole not 7/64".
51 April 1992 60 High Chair Base illustration: no holes on top of part D.
51 April 1992 61 High Chair Seat illustration (right corner): 1 1/2" not 1 1/8"; Step 3, do plug the holes; Step 5, 5° not 10°.
51 April 1992 62 High Chair Support Detail: only 1 screw in L/M not 2.
51 April 1992 63 High Chair Buying guide tray new address: Rockler, 4365 Willow Dr., Edina, MN 55340.
51 April 1992 63 High Chair Buying guide Miller Hardware address: 1300 ML King, Des Moines, IA 50314.
51 April 1992 72 Buying Boards See Talking Back issue 54, September 1992, p. 6 for reader letter.
52 June 1992 41 Sharpening Carving Tools Buying guide new source, polishing compound: Wood N' Things, Inc., 208/375-9663
52 June 1992 55 Classic Column Buying guide new phone: 800/321-6840
52 June 1992 59 Porch rocker Rocker Lamination: 1 3/4" dadoes not 1 1/2"; End Frame Assembly: missing dimension part B 14 3/4".
52 June 1992 64 Woodie revival Photo caption: woodwork is by Ohioan Steve Glasier
53 August 1992 46 Tin punching Buying Guide: Country Accents new address and phone 570/478-4127, 1723 Scaife Road, Williamsport, PA 17701
53 August 1992 51 Pie Safe Buying Guide tin panels: area code change 570/478-4127; Hardware: polished brass latch with catch
53 August 1992 78 Wagon Front Wheel Support: front edge of H not I; struts L = 5 1/2", trim 3/4" for K
53 August 1992 79 Wagon Cutting Diagram: part P from Walnut not Walnut Plywood; Bill of Materials: G 1" Thick, L 5 1/2" Length
54 September 1992 69 Workbench Buying Guide: Woodworker's Vise is no longer available, use vise of own choice
54 September 1992 72 Idea Shop stool Tenon illustration: for part A the glue line is on the adjacent face; 1/4" for part C not 1/2"
54 September 1992 77 Wall Cabinet System Exploded View: Change 3/4x2 inch non-mortise hinge to 7/8x2-1/2 inch non-mortise hinge
54 September 1992 79 Wall Cabinet System Buying Guide: Hardware kit no longer available. Wire pull no. 39768, magnetic catch with strike plate no. 29280, no-mortise hinge no. 90434. Rockler Woodworking and Hardware, 800/279-4441 or www.rockler.com
54 September 1992 81 Workshop Clock Buying guide clock parts: Quartz clock movement #10002; hands #66995; face and bezel assembly #27029
55 October 1992 37 Shaker-style tall chest Divider (D) bottom measurement: 5 5/8" not 5 3/8". See Talking Back, issue 62, August 1993, page 11.
55 October 1992 40 Shaker-style tall chest Step 3: "over the front edge of the top shelf (C)."
57 December 1992 61 Train Cut the Parts, Step 1: part B 12 1/4" length; Parts View: part B not A for Pilot/Chassis; width 7/16"+2 5/8"+7/16"; 7/8" should be 15/16"
57 December 1992 62 Train Locomotive: Part D, 1 1/4" to center of hole is 1 1/8"; Part C, width is 2 5/8" not 2 1/2"
57 December 1992 63 Train Bill of Materials: C 2 5/8" width; F 2 3/4" long.
57 December 1992 65 Train Buying Guides are no longer available, no other sources found
57 December 1992 68 Periscope Final assembly, step 2: "Position the router table fence 1 1/4" from the center of the bit." "front piece (B)" not (A).
58 January 1993 49 Router retrofit Buying Guide, Router plate: Insert plate 3/8x12x12" acrylic no. 16L71. Woodcraft, 800-225-1153, woodcraft.com
58 January 1993 61 Blanket Chest Lid Support: part P should be Q; part B should be R. Note: measure for the hinge pilot holes
58 January 1993 81 Router-fence system safety guard Width end of acrylic top is 3 7/8"
59 February 1993 34 Baby's first bed Bill of Materials: Part A is 43 7/16" long
59 February 1993 35 Baby's first bed Top edge of cornerpost (A) no higher than 1/16" above top edge of (B).
59 February 1993 36 Baby's first bed Taper Detail, 43 7/16" to bottom of post; Corner Posts, right leg, top, 1 1/16" from center of hole to top, 5 5/16" from center of hole to top
59 February 1993 39 Baby's first bed Guide Rod: 5/8" between corner post bracket and "S" bar mounting plate
59 February 1993 42 Random-Orbit Sanders Porter-Cable 333 not 7336
59 February 1993 45 Random-Orbit Sanders Porter-Cable 7336 not 333
59 February 1993 52 Dining Table Step 5 and 6: Base drawing is Crossmember drawing
59 February 1993 56 Dining Table Buying Guide: kit discontinued. Tabletop fasteners #34215, T-nuts #26054, floor guides #18657, and extension slides (wood #29496 or steel #29694); available from Rockler at 800/279-4441 or rockler.com; table aligners #JH 3 available from Woodworker's Hardware at 800/383-0130 or wwhardware.com
59 February 1993 68 Birdhouse Cutting Diagram: bottom right corner, 4 1/4 should be 4 1/2"
60 April 1993 60 A Credenza With Charisma Door and Side Frames: Part B, width 1 1/4"
60 April 1993 61 A Credenza With Charisma Glass-Stop Positioning Jig: 1 1/8" wide; 1/2" should be 3/8"
60 April 1993 62 A Credenza With Charisma Section View, Glass Shelf: 13 3/8" + 31 1/8" + 13 3/8"
60 April 1993 75 Dining Chairs Bill of Materials: Part D 15 5/16" length
60 April 1993 76 Dining Chairs Side Frame Assembly: Part D is 15 5/16" length
61 June 1993 27 Willow Works Address: The Wonderful Willow Works, 755 Main St., Belgium, WI 53004
61 June 1993 59 Rocking Snail Measurement from the front edge of the slats to the front of the body should be 3 1/2"; Antennae pegs should be shortened to 1" in length and the mounting holes drilled 1" deep. Making the antennae small round knobs.
62 August 1993 34 High and Mighty Tablesaw Jig Buying guide changed to Schlabaugh & Sons Woodworking, 800/346-9663. Stock no. TJ-101.
62 August 1993 36 Raised Panels and Frames The exact angle of the saw blade to cut bevels on raised panels will vary according to the width of the reveal.
63 September 1993 23 Fold-Out Work Supports Side, width: 35 1/4" not 37 1/4"
63 September 1993 34 Tall Clock Cutting Diagram: 1/4x24x96" Oak plywood
63 September 1993 36 Tall Clock Marking the hole locations: both end 3/4" should be 3/8"
63 September 1993 38 Tall Clock New supplier for clock parts: Schlabaugh & Sons Woodworking, 800/346-9663.
63 September 1993 46 Sees & Such Snack Shop Change "However, birds that typcically feed on the ground, like cardinals and juncoes, use a crevice in a tree bark to hold their seed while they peck it open." to "However, cardinals and juncos use the platform board. Nuthatches wedge seed into a crevice to peck."
63 September 1993 56 Intarsia Coatrack Pattern: eye made out of Maple
64 October 1993 78 Shaker bed Buying Guide, hardware kit: Bed bolt covers JG-226 changed to KK-22. Stock no. WMBD KIT no longer available. New address and phone: Hershberger Hardware, 1411-TR178, Baltic, OH 43804, 800-734-8044.
65 November 1993 38 Sears Whole Shop
Dust Collection Kit
Kit #29964 for manifold system
65 November 1993 60 Ageless Urn Carrier board stave pocket should be 8 7/8" long. Stave pocket depth 1 1/2"; stave width 1 1/2". New Bill of Materials in April 1994, page 8.
65 November 1993 69 Block Quilt Hanging Miter-Cutting the Diamonds: from blade should be 7/8" not 1"
66 December 1993 35 Fastening Tools Jet 800/274-6848
66 December 1993 36 Teddy Bear Chair Step 2: 3/4"-thick cherry to 1 5/8"x18 1/4"
66 December 1993 37 Teddy Bear Chair Exploded View: Part E, 6 1/4" from top of leg to seat top
66 December 1993 37 Teddy Bear Chair Backrest: Part B, 11 3/4" should be 11 1/8"; 8 1/4" should be 7 1/8"
66 December 1993 40 Teddy Bear Chair Final Assembly: Top (A) 11 3/8" should be 10 1/4" to top of armrest
66 December 1993 41 Teddy Bear Chair Full-sized front leg patterns: 5 1/2" should be 6 5/8"
67 January 1994 15 Shop Tip Misspelled name David Hogue
67 January 1994 35 Miter Jig Bill of Materials, part J, 2 pieces not 4
67 January 1994 37 Miter Jig Handle Pattern: 1/4" too short, goes over polycarbonate too
67 January 1994 39 Miter Jig Buying Guide: price should have been $49.95 as of 4/94
68 February 1994 34 Country Cabinet Stanley hinges are no longer available. See plan DP-00060 for updated project.
68 February 1994 35 Country Cabinet Cutting Diagram: board for U,T,V,Y should be 3/4x9 1/4x96" Pine
68 February 1994 35 Country Cabinet Upper Molding Detail: label G should be H and label H should be G
68 February 1994 35 Country Cabinet Lower Molding Detail: label H should be F and label G should be H
69 April 1994 26 Ask WOOD The Crafts Fair Guide zip code is 94942
69 April 1994 73 Safari Puzzle Full-Sized Pattern: dog pattern should be labeled MW
69 April 1994 76 Country Chair End View: lines for locating dowel hole centerpoints should be 7 1/4" not 4 7/16"
72 September 1994 34 Roll-Around Plywood Cart Side View, End Panel A: top, 3" should be 2 1/4; angled side edge, first 18 3/4" should be 18 1/4"
72 September 1994 49 Mobile Workbench Buying Guide, Vise. Record vise is no longer being manufactured, use vise of own choice.
72 September 1994 50 Mobile Workbench Under "It's time to add the vise," step 1: Record vise is no longer being manufactured, use vise of own choice.
73 October 1994 47 The Perfect Polyurethane The Flecto Co., Inc. 800/635-3286 U.S./800/387-3625 Canada
73 October 1994 57 Biscuit Joiners Notes 1- 4 missing: 1. (HH) Hand-held (ST) Stationary (*) Designed for use with drill press; 2. (B) Belt (D) Direct (G) Gear (*) Machines have a slip clutch for preventing kickback and extending motor and gear life; 3. (E) English (M) Metric; 4. (A) Adjustable (F) Fixed (0° and 45° only) (*) Adjustable fence available (#) 0° only
73 October 1994 75 Tureen Buying Guide: 801/266-1578
74 November 1994 74 Corner Classic Update, Step 4: where shelves (E) fit into dadoes into sides (C) cut 1/8" shorter the shelves (D). This will allow wood movement to slide in and out of dadoes.
74 November 1994 76 Corner Classic Update, Step 2: after top and bottom are installed, now install shelves D and E. Note: Do not glue E in place, the shelves must be able to move. Fasten with screw in the corner where A and B are joined with one screw 4" in A and one screw 4" from corner in B.
75 December 1994 35 Scrollsawn Ornaments Super Scrollsaw Patterns is no longer published
75 December 1994 56 Dresser-Top Delight Bill of Materials: parts L,M,N width is1 3/32"; R width is 3 7/32"; S width is 5 7/32"; T width is 11 7/32"
75 December 1994 63 Snow Globe Buying Guide: Craft Supplies USA is no longer sourcing the snow globe
75 December 1994 69 Shop Clock Buying Guide, Engraved Plate: As of August 2001 cost is $10 per plate, address changed Custom Awards, 9200 Hickman Road, Suite S, Des Moines, IA 50325.
75 December 1994 73 Snowman Buying Guide, new address: Roberts Studio, 2620 Heather Road, Seymour, TN 37865, 800/316-9010
75 December 1994 74 Pee-Wee Starter Set (golf) Supplies: 3/16x1 1/4" carriage bolt not 13/16"
75 December 1994 104 Finishing Touches Only the brochure is free, not the book
76 January 1995 43 Pocket-Hole Joinery Trend-Lines 800/767-9999
76 January 1995 57 Notable Door D?cor Buying Guide, tuned chime rods, are no longer available.
76 January 1995 61 Portable Planer

Original project designed for a 10" planer, new dimensions are for 12" planer: Exploded View: width of I should be 21 1/4"; width of K + L's should be 21 1/8"; Side Panel: 2 1/2" between top edge and holes should be 4"

76 January 1995 62 Portable Planer Bill of Materials: E length is 22"; F length is 21 1/4"; G length is 21 1/4"'
I width is 21 1/4"; K width is 20 5/8"; M length is 20 5/8"
76 January 1995 63 Portable Planer Parts View: part J 1/4"-wide slots 1 1/2" long
77 February 1995 39 Slow-Speed Grinders Penn State 800/377-7297
77 February 1995 45 Develop Your Shop Skills To get the proper measurement when starting to measure from the 1" mark on a tape, add 1" to the desired board length.
77 February 1995 57 Plant Stand Buying Guide: Leichtung Workshops no longer sourcing the material
77 February 1995 65 Mission Buffet Buying Guide no longer available. Substitute pulls: Drawer pull item 01G60.10 and door pull item 01G60.20; hinge item 02H10.04 available from Lee Valley, leevalley.com or 800/871-8158; door catch item 27H03 available from Woodcraft, woodcraft.com or 800/535-4486
77 February 1995 70 Bird Houses Illustration: top and bottom 2x4s 8 29/32" apart
77 February 1995 71 Bird Houses Bird Feeders: Step 3, third line, concrete-coated should be resin-coated.
77 February 1995 72 Bird Houses Wood Duck Nest Box: 25 3/4" should be 26 3/8"
77 February 1995 72 Bird Houses Wren House: 1" hole, dimension to center of hole 1 1/2"
78 April 1995 64 Federal Mirror Routing the Cove: E is 3/8" thick, cove is 1/4" deep, so there should be only 1/8" in contact with pilot bearing.
78 April 1995 65 Federal Mirror Bill of Materials: Part B, width is 6 1/2"; Screw-Hole Detail, 3/8" plug 5/16" long
79 June 1995 42 One Cool Cabinet
(ice box)
Buying Guide Hardware change to Van Dyke's 800/558-1234 or go to vandykes.com. Brass elbow catch no. 02230503; icebox label no. 02220063; 2 pair of offset hinges no. 02222905; right-hand latch and catch no. 02243872; one pair of combination hinge and lid supports no. 02285835.
79 June 1995 44 Radial-Arm Saw Stop Pattern Pack: missing dimension on part B, 5/32" holes countersunk
79 June 1995 53 Easy Glider Pattern Pack: back slats, where you see the symbol ø substitute the fraction 11/16".
79 June 1995 56 Easy Glider Exploded View: assembly with parts A/B/C/D/E 1/4x2 1/4" R.H. machine screw
79 June 1995 57 Easy Glider Supplies: 1/4x2 1/4" roundhead stainless steel machine screws
79 June 1995 57 Easy Glider Bill of Materials: Part U, length 56 1/2"
79 June 1995 57 Easy Glider Buying guide: New address McFeely's, PO Box 11169, Lynchburg, VA 24506-9963 or call 800/443-7937
79 June 1995 69 Teeter-Totter Bill of Materials: Part E, length 9 1/4"
80 August 1995 73 Tanglewood Fireball Pendant "Stive to make the strands a constant diameter (about 5/32" is good).
81 September 1995 26 Tool Buyer's Update Detroit Radiant Products Co. new #800/222-1100
81 September 1995 41 Canoe Craftsmanship/Bumbaca Paleo Canoe Co. is out of business
81 September 1995 42 Coffee Table Pattern Pack: build the table leg using the measurements in the article and correct the measurements on the pattern to match those of the article. (see article-pages 42-47)
81 September 1995 44 Coffee Table Buying Guide is no longer available
81 September 1995 64 Gardener's Gold Mine Source for cedar post top balls no longer available. 
82 October 1995 18 Shims Veritas dado shim set sold by Veritas Tools 800/667-2986 and protected by patent.
83 November 1995 64 Country Plate Rack for missing full-size pattern, send self-addressed stamped envelope to WOOD magazine, 1716 Locust, LS221, Des Moines, IA 50309-3023
83 November 1995 69 Timeless Timekeeper Buying Guide update: Supplier for quartersawn oak no longer available.
83 November 1995 70 Child's Activity Center step 3, reference should be page 30
83 November 1995 78 Home Computers foot note: page reference should be page 82
83 November 1995 79 Home Computers KnotWhole Publishing is out of business.
84 December 1995 82 Craftsman-Style Shelf Section View: both parts should be 1/2" not 3/4"
85 January 1996 47 Router Accessories Eagle America: featherboard and stop block for the fence shown in photo is not included in this package. These are sold separately as accessories. The metal table legs are not an Eagle America product. They sell a hardwood table-leg assembly.
85 January 1996 55 Cradle Buying Guide: new source for keyhole shelf hangers, Rockler 800/279-4441 Single #28837, double #28829
86 February 1996 40 Drill-press table Ready-to-assemble kit is no longer available.
86 February 1996 74 Kit Furniture Grand River Workshop is out of business.
87 April 1996 58 Far East Desk Chime Buying Guide, chime rods, are no longer available.
88 June 1996 39 Patio Table/Benches Bill of Materials: Part E, length 5" not 4 1/2"
88 June 1996 43 Patio Table/Benches Cutting Diagram: 60" cedar boards should be 72"
88 June 1996 54-55 Scrollsaw Applique Fuschia stencil from StenSource International is #W9514 Contact StenSource at www.stensource.com or call 800/642-9293
88 June 1996 66 Treasure Tower for missing full-size pattern, send self-addressed stamped envelope to WOOD magazine, 1716 Locust, GA310, Des Moines, IA 50309-3023
89 August 1996 24 Shop Tips Illustration: 1/4" plywood front should be 7" not 6"
90 September 1996 47 Shaker Nightstand Buying Guide: Preturned legs are no longer available.
92 November 1996 58 Down-Home Sideboard Buying Guide: Router bit Freud #99-240 drawer lock bit available from Freud at 800-334-4107 or freudtools.com. Hardware from Constantines is no longer available.
92 November 1996 63 Country Lamp Wiring diagram: The silver colored screw is the neutral, but it should be attached to the ribbed conductor. The broadest blade on the plug is neutral, not hot as originally shown. See Talking Back August 1997, page 4 for illustration.
92 November 1996 73 Farm Truck Buying Guide update: Cherry Tree Toys no longer selling spoked wheels; Hardwood kit and spoked wheels available from Hertiage Building Specialties; Toy plans catalog no longer available by mail, see www.baldwintoys.com
93 December 1996 61 Junior Jalopies Chassis Exploded View: to receive axle peg, 1/4" hole should be 3/16" hole
93 December 1996 73 Universal Tablesaw Jig Buying Guides for Hardware kit and Ready-to-assemble kit are no longer available.
94 January 1997 47 Punched-tin wall cabinet Buying Guide. Country Accents new address and phone: 1723 Scaife Road, Williamsport, PA 17701, 570-478-4127
95 February 1997 13 Quick-Grip clamp helps keep crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
95 February 1997 24 Dovetail-Jig Stabilizer Fence Exploded View: A is 12" wide; Porter-Cable model 5008 Dovetail Templet is no longer available.
95 February 1997 67 Wiring Your Shop see Talking Back, August 1997, page 10.
A subpanel requires two separate bus bars, one for the ground wires and one for the neutral wires. The ground bus bar amounts directly to the panel box, and the neutral bus bar should rest on an insulating block to keep the neutral wires from contacting the panel box. Also, in a subpanel, the ground wire must come from the main service entrance panel to provide a "least resistance" ground path for any fault current. Remember, don't take chances with electricity. Always consult local codes and get the advice of a certified electrician before beginning any do-it-yourself electrical work.
97 June 1997 71 Saw and save by milling your own lumber New address: Granberg International, PO Box 2347, Vallejo, CA 94592-0347; phone 800/233-6499
98 August 1996 79 The WOOD Gang Builds Kit Boats Paleo Canoe Co. is out of business
98 August 1996 92 Grand Humidor Buying Guide-sources no longer available, no replacement available
99 October 1997 36 Dining-Table Duo Buying Guide: 6" peppermill mechanism part no. 365-0006; rubber bung part no. 123-0148
99 October 1997 55 Mobile sanding center Buying Guides of vacuum and dust-collection system are no longer available
99 October 1997 57 Ikebana Vase Buying Guide changed to Craft Supplies USA, 800/551-8876, www.woodturnerscatalog.com, part 183-0200
100 November 1997 54 Dust-Defying Cyclone Muffler for cyclone, see Talking Back, issue 101, December 1997, page 8
100 November 1997 67 Roll-Around Tool Base Exploded View: part B 1 1/4" measurement bottom of where E meets part B
100 November 1997 73 Portable Belt Sanders Bosch: sanding frame accessory not available
100 November 1997 79 Two-wheeler bike Handlebar pattern (pattern pack): 1/8" pilot holes should be 3/16"; add 1/4" to cutline

 

Issues 101-150
WOOD MAGAZINE CHANGES / UPDATES Issue 101-150
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
101 December 1997 57 Portable Base (lathe) Bill of Materials: Part B thickness is 1/2"
101 December 1997 63 Fabulous Fireplace Surround Buying Guide: Change The Woodworkers' Store to Rockler Woodworking and Hardware, same phone number
101 December 1997 84 Nativity Scene Sheep, Manger, and Donkey: 1" stock; remainder 1 1/2" stock
102 Winter 1997 8 Talking Back Homemade knob for tenoning jig: illustration 1 3/8" should be 1 5/8".
102 Winter 1997 8 Talking Back Homemade knob for tenoning jig: illustration 1 3/8" should be 1 5/8".
102 Winter 1997 58 Full-Service Workbench Bill of Materials: part P and Q width should be 4 1/2 not 5 1/4"
102 Winter 1997 58 Full-Service Workbench Buying Guide Vise: Part no. 126504. New address: 1177 Rosemar Road, P.O. Box 1686, Parkersburg, WV 26102
102 Winter 1997 60 Full-Service Workbench Drawer illustration, left side: Q should be 4 1/2" not 5 1/4"
102 Winter 1997 65 Wet-Wheel Grinder Buying Guide: Hardware kit is no longer available.
102 Winter 1997 84 Super-Simple Taper Jig Buying Guide Hardware Kit is no longer available.
103 February 1998 30 Tips From Your Shop (And Ours) Swing-out rack, top section view: pegboard should be perforated hardboard.
103 February 1998 43 Pendulum Clock Step 2: dowel (E) not (F)
104 March 1998 45 Swivel-Topped Tool Cabinet Step 8: use locking swivel and fixed casters
104 March 1998 46 Swivel-Topped Tool Cabinet Supplies: use 2–2 1/2" locking swivel casters
104 March 1998 47 Swivel-Topped Tool Cabinet Exploded View: 2 1/2" locking swivel caster
104 March 1998 57 Compound Mitersaws Caution: Always be sure that the plate that covers the arbor screw is securely held in place by the rubber washer and screw. See Talking Back issue 110, December 1998, p. 8
104 March 1998 68 Entertainment center Buying Guide, Hinges. 170 degree overlay Modul hinges, part 00B0401, available from Lee Valley 800-871-8158 or leevalley.com
104 March 1998 69 Entertainment center Panel Mounting Detail illustration: sheet metal screw not wood screw
105 April 1998 16 Ask WOOD (Ni-Cad batteries) How to dispose of them see Talking Back, issue 116, August 1999, page 6
105 April 1998 47 Patio Chair Address for WOOD Magazine Plans, PO Box 349, Kalona, IA 52247, or call 888-636-4478, or online at woodstore.woodmall.com
105 April 1998 63 Computer Center Bill of Materials: Part II, 13" width not 13 1/4"
105 April 1998 63 Computer Center Hardware source, new address: Rockler Woodworking and Hardware, 800/279-4441 or www.rockler.com
105 April 1998 66 Computer Center Drawer Cabinet and Drawers illustration: part CC front side should be 3/4" rabbet 1/4" deep
105 April 1998 77 Windchime Chimes made of 3/8" diameter aluminum rod, available at hardware stores and home centers. The lengths are: 7-1/2", 6-7/8", 6-1/2", 5-15/16", 5-5/8", 5-5/16", 4-7/8", 4-5/8"
105 April 1998 78 Music in the Wind Buying Guide, tuned chime rods, are no longer available.
105 April 1998 81 Adjustable Square Exploded View, part B: the hole size for the brass threaded insert may vary for some inserts.
106 June 1998 43 Patio Planter/Table Bill of Materials for the Planter not Table
106 June 1998 45 Patio Planter/Table Address for WOOD Magazine Plans, PO Box 349, Kalona, IA 52247, or call 888-636-4478, or online at woodstore.woodmall.com
106 June 1998 47 Bird Bath Note: glue needs to be water resistant
106 June 1998 68 Keepsake Box Forming the Lid Profile and Forming the Base Profile illustrations: 3/16" cove bit not round-over bit.
106 June 1998 68 Keepsake Box Illustration for Cut 4: 3/16" should be 1/8".
107 August 1998 43 Nautical Knickknack (shelf) Buying Guide: Hardwood kit, call for current price. Finished boat and brochure no longer available. Visit Jim Shotwell's website at jimshotwellboats.com.
107 August 1998 57 Scrollsawn Basket Pattern Pack for parts C and E: the centerline needs to be moved up 1/8" to go through the middle of the beads.
107 August 1998 94 Saw-Top Dust Collector Illustration: labels for 3/8" and 3/4" screws switched
108 October 1998 8 Climb Cutting How Climb-Cutting Give Smoother Results: Shape of bit should be round not oval
108 October 1998 46 Box-Joint Jig Adjustment Assembly: Part I 13/32" hole should be 1" from the end, not 2" as shown.
108 October 1998 46 Box-Joint Jig Buying Guide: Hardware kit and Easy-to-assemble kit are no longer available.
108 October 1998 47 Box-Joint Jig Cutting Diagram: by shortening the length of pieces A, C, and D from 26" to 23-7/8", and rearranging the cutting diagram, it is possible to get two complete sets of pieces with indexing blocks from a 24x48" piece of plywood.
108 October 1998 50 It's a Keeper (magazine box) See Sounding Board, issue 156, June/July 2004, page 10, new dimensions to accommodate increase in WOOD magazine size
108 October 1998 52 Nightstand Glue up the sides, step 1, page 54 not page xx; step 2, page 54, not page xx.
108 October 1998 54 Nightstand Buying Guide: Mission-style small pull 2-3/4x1-3/4 inches, no. 01G62.70, available from Lee Valley, 800-871-8158 or leevalley.com
108 October 1998 67 Entertainment Extravaganza Buying Guide: Overlay carrier strip should be Inset carrier strip. Parts update: Rockler slides no. 35571; strip and hinges no. 35663. Use crown molding bit of choice. MLCS bit #870 is no longer available.
108 October 1998 71 Entertainment Extravaganza Exploded View: parts C front-left corner are not notched as illustrated.
108 October 1998 71 Entertainment Extravaganza Bill of Materials: Part C, L = 17 1/4" not 17 3/4".
108 October 1998 82 Drafting/Reference Center

Self-closing hinge should be 12" not 14". Available from:
Woodworker's Hardware (#KV8080 PEZ12) 800/383-0130. Arrow for 1/4x3/4x15 1/2 maple goes to front edge of board for a band. New Buying Guide for 4-position multiuse bracket (3/03) is now Woodworker's Hardware (800/383-0130) #KV0206 ZC 12.

109 November 1998 10 Workbench Tool Crib End Detail: 3/8" hole should be 1 3/4" from edge
109 November 1998 45 Resawing Illustration BLADE GUIDE 1 5/8" should be 2 3/8"
109 November 1998 70 Noah's Ark Buying guide Ark animals: New address Roesner's Miniature, Menagerie, 425 Overlook Court, Geneseo, IL 61254, aminizoo.com, phone 563-565-3489, no fax or e-mail address available. Contact for current prices.
109 November 1998 80 Tilt-Top Router Table The model 300 Incra jig originally used with this router table top is no longer available. To accommodate this, we designed a new fence to replace this jig. The revised instructions and drawings are available as downloadable plan (DP-00064) in the Shop Tools and Accessories section of the WOOD Store at woodstore.woodmall.com
110 December 1998 32 Ask WOOD Illustration Face-Jointing: The tangential surface shrinks about twice as much as the radial surface. Lumber always cups to the bark side.
110 December 1998 55 Turning Back the Times Source new addresses: Ornamental Turners International: Alan Bugbee, 37 Fox Den Road, West Simsbury, CT 06092; Society of Ornamental Turners, Secretary Nicholas S. Edwards, Kirklea, Park Road, Melchbourne, Bedfordshire, MK44 1BB, UK
110 December 1998 56 Steamer Trunk Hardware. 4 bump glides, 02240624; 2 handles, 02263766; 4 handle loops with pegs, 02003428; 4 stop hinges, 02003522; 1 lift pull, 02264230; 2 draw bolts, 02240856; 2 trunk stays, 02003530. Call VanDyke's Restorers 800/787-3355 to order.
110 December 1998 Pattern Five-Drawer Chest Base: Part I, counterbore 2" from front not back
110 December 1998 68 Five-Drawer Chest Buying Guide, hardware: Woodworkers' Store now Rockler Woodworking and Hardware
110 December 1998 68 Five-Drawer Chest Buying Guide, turned feet: address changed to PO Box 728, Morristown, TN 37815
110 December 1998 69 Five-Drawer Chest Cutting diagram duplicated from page 68. See issue 111, page 8, for the cutting diagram.
110 December 1998 72 Country Finish Buying Guide: Zar products listed are no longer available. Use finish brand of own choice.
110 December 1998 83 Mobile bases Detla's phone number 800/438-2486
111 Winter 1998 49 Bent-Laminated Hang-Ups Buying Guide update: Call for current prices. In Canada call: 952/471-8550.
111 Winter 1998 64 Country-Fresh Dresser Slot Detail: rabbet on part C not part A.
111 Winter 1998 65 County-Fresh Dresser Buying Guide, turned feet: new address PO Box 728, Morristown, TN 37815
111 Winter 1998 67 Country-Fresh Dresser Photo B, top row should be four part R, not R and P.
111 Winter 1998 77 Step right up Base hypotenuse dimension is 9-13/16" not 8" as shown.
112 February 1999 47 Mesquite Magic Update seminar, plans, and material information: Four-day seminars, available from www.mesquiterocker.com, Robert Hensarling, 4326 East Main Street, Uvalde, TX 78801.
112 February 1999 53 Morris Chair Opening paragraph: We do not have a mail-order source for the cushions.
112 February 1999 54 Morris Chair Photo A: phone is flopped. The handle should be on the right.
112 February 1999 55 Morris Chair Plan WP-JG-1002, call 888-636-4478 or online at woodstore.woodmall.com
112 February 1999 58 Morris Chair Drilling the pin holes: the pin-hole locator jig is not flush with the end of the arm, IMPORTANT to be flush with the backrest of the chair (see step 8)
112 February 1999 Pattern Morris Chair Part I (Armrest): see Talking Back issue 115, June 1999, page 8, for dimensions and delete the 3" dimension in the upper left hand corner of the template form.
112 February 1999 63 Now You're Cookin' Buying Guide new address: Mike and Rox Duflo, 2555 20th Ave., Vero Beach, FL 32960-4145, www.woodduflo.com
112 February 1999 68 Oscillating Spindle Sanders Grizzly MS-240 discountinued, replaced with G1173 at $150
112 February 1999 81, 82 Lathe Artistry The thickness of the maple strips for the layer 11B laminations, shown on the last line of the first chart on page 81 should be 3/16" instead of the 1/8" listed. The pieces are shown also in the lamination on the right side in the Feature Ring Blanks illustration page 82. On drawing, change the 1/8" dimenions for the two light-colored strips to 3/16".
112 February 1999 83 Lathe Artistry Buying Guide for wood kit is no longer available.
113 March 1999 26 Nightstand Buying Guide, turned feet: new address PO Box 728, Morristown, TN 37815
113 March 1999 60 Bandsaw Multi-Jig It is important that the angle of the trammel be 90° from the front edge of the blade.
113 March 1999 63 Bandsaw Multi-Jig Parts View, Slot Detail: 1/4x1" slot should be 1/2x1" slot.
113 March 1999 68 Wood by the Yard Caution regarding photo on page 68, always use wedges for splitting wood. See Talking Back, issue 116, August 1999, page 6.
113 March 1999 83 Shelf Clock Clock Face illustration: 3/16" hole should be 5/16".
113 March 1999 83 Shelf Clock Bill of Materials: Part E, 1/8" thickness is 1/16". Part G, 11" length is 12 1/4".
113 March 1999 85 Shelf Clock Full-size clock hand patterns: Use a #10 drill bit for part F. Use 5/32" hole for part E.
Cutting Diagram: part E 1/16" thick stock
114 April 1999 16 Panel-Cutting Sled The 1" hole is for hanging the sled when not in use
114 April 1999 58 Stains Olympic review in Talking Back, issue 119, December 1999, page 8.
114 April 1999 61 Stains Valspar number is 800/323-5129
114 April 1999 66 Solid Oak Bed Buying Guide, turned feet: new address PO Box 728, Morristown, TN 37815
114 April 1999 66  Solid Oak Bed Exploded View: Part L 1 1/8 inch hole should be 7/8 inch deep
114 April 1999 75 The Great Cover-Up Buying Guide new address: Constantine's Wood Center, 1040 E. Oakland Park Blvd., Ft. Lauderdale, FL 33334, 800/443-9667. Kit no. WDVK2 no longer available, order parts separately.
114 April 1999 75 Showy Keepsake Box Buying Guide new address: Constantine's Wood Center, 1040 E. Oakland Park Blvd., Ft. Lauderdale, FL 33334, 800/443-9667. Kit no. WDVK1 no longer available, order parts separately.
115 June 1999 Pattern Knockdown Sawhorses Stretcher End: Align the upper angled cut, opposite the hanging hole, with the inside edge of the bottom notch
115 June 1999 43 A Crown Jewel (clock) Mitersaw Table Section View: reverse part A, the rabbetted edge should be against the fence not the guide strip. (See Talking Back issue 117, October 1999, page 4.)
115 June 1999 43 A Crown Jewel (clock) Buying Guide: Clock hardware kit is no longer available. Company is no longer in business.
115 June 1999 59 Sidewalk Speedster Source for wheels: see issue 118 page 6
115 June 1999 59 Sidewalk Speedster Body Side: lower left corner of illustration 1-1/16" should be 11/16".
115 June 1999 60 Sidewalk Speedster

Bill of Materials: Part P thickness should be 5/8" not 3/4". See issue 118 page 6.

115 June 1999 63 Sidewalk Speedster Step 4: Krylon no. 1315 cherry red is now Krylon no. 2101 cherry red.
115 June 1999 65 Masterful Marking Gauge Buying Guide parts are no longer available.
115 June 1999 Pattern Folding Adirondack Chair Seat Support (H), top of part F 30° bevel should read 40° bevel. Bottom of part F should be 20° bevel. Correct in other illustrations.
115 June 1999 72 Folding Adirondack Chair Foot note: See Talking Back issue 118, page 8, for collapsible adjustment.
116 August 1999 Pattern Casserole Carrier Base should measure 16 1/4" not the 16 1/2" that it does measure.
116 August 1999 55 Arbor Bill of Materials: The lattice stop widths are G=1"; H=1 3/8"; I=1 3/8"; J=1"; K=1 3/8"; L=1"
116 August 1999 64 Bookcase Buying Guide, hardware update: Parts #123876 and #123872 no longer available. Use 2 Mission-style vertical door pulls, #01W32.12, LeeValley at leevalley.com or 800/871-8158. 3 dark antique finish left-handed lift-off hinges, #LO-8L, 3 dark antique finish right-handed lift-off hinges, #LO-7R, Horton Brasses Inc. at horton-brasses.com or 800/754-9172. Remaining hardware available through Woodcraft. Note: Original hinges used on the bookcase were no-mortise. These hinges must be mortised into the case and door.
116 August 1999 69 Bookcase Door illustration: 2° bevel on inside edge of each door not outside edges. Arrow direction moves to the other side of door illustration. The dadoes in parts U and V should be 1/2" by 1/4" deep, not 1/4" dadoes 1/4" deep.
117 October 1999 46 Schoolhouse Clock Bill of Materials and Parts View (pattern): Part K is 3/4" wide not 1" wide
117 October 1999 46 Schoolhouse Clock Buying Guide: Spring wound movement no longer available; battery movement available
117 October 1999 47 Schoolhouse Clock Exploded View: #8 x 3/4" F.H. wood screws (for mounting J to Ks)
117 October 1999 47 Schoolhouse Clock Exploded View: Glue (H and I) to back side of (L) 3/16" from outside edge.
117 October 1999 Pattern Schoolhouse Clock Parts View: Part D length is 20 7/8" not 2 7/8".
117 October 1999 55 Stylized Bird Stylized bird pattern missing from pattern insert. See issue 119, page 8 for pattern.
117 October 1999 70 Ironing-board hideaway Buying Guide, hardware: Ironing board cover 130350 no longer available, see chain department stores; 1-1/4" brass knob part number changed to 130161
117 October 1999 85 Letter Box Section View: Part E does not go to the top of Part A.
118 November 1999 44 Shop-Made Hardware Part no. change: square file, catalog no. GRO-32-421 from Reid Tool Supply Co.
118 November 1999 48 Shop-Made Hardware New source: green patina available at craft and art supply stores.
118 November 1999 48 Shop-Made Hardware New phone number: Constantine's Wood Center, 800/443-9667.
118 November 1999 55 North-Country Windsors Source e-mail: bob@bobdillonwindsorchairs.com
118 November 1999 59 Table lamp Hardware kit is no longer available (September 2006)
118 November 1999 63 Tablesaw Accessories Cabinet Buying Guide and Exploded View: Woodcraft's part numbers changed, swivel casters (2) 141050, fixed casters (2) 141053; 3" wire pulls (2) no. 836159.
118 November 1999 66 Portable Mitersaw Stands Upgrades to Delta's and Stablemate's mitersaw stands. See Talking Back issue 119, December 1999, page 8.
118 November 1999 82 Big Rig Bill of Materials: Part C should be 6" width, 7 3/8" length
118 November 1999 86 Nutcracker See Talking Back, Issue 125, August 2000, page 12, for tip on cutting grooves on ends of parts A and B.
118 November 1999 87 Nutcracker Cutting Diagram: Brass sheet should be 1/16x2x15".
118 November 1999 87 Nutcracker Buying Guide new address: Constantine's Wood Center, 1040 E. Oakland Park Blvd., Ft. Lauderdale, FL 33334, 800/443-9667
119 December 1999 53 Quilt Stand End Panel: R=5" goes to edge of panel.
119 December 1999 55 Quilt Stand Step 1: spacing between stopblock and guide blocks is 3/4" not 1/2"
119 December 1999 62 Mobile Mitersaw Center Bill of Materials: Part Q is 13/16" thick. See Talking Back Issue 127, October 2000, page 8, for cutting diagram. Woodcraft's part numbers changed, swivel casters (2) 141050, fixed casters (2) 141053; 3" wire pulls (2) no. 836159.
119 December 1999 62 & 63 Mobile Mitersaw Center Buying Guide and Exploded View: Woodcraft's part numbers changed, swivel casters (2) 141050, fixed casters (2) 141053
119 December 1999 63 Mobile Mitersaw Center Front Section View drawing: hinge butts up to Part T. See Exploded View drawing (above).
119 December 1999 70 Drill-Press Dust Collector See Talking Back, Issue 125, August 200, page 12, for reader suggestion.
119 December 1999 81 Wake-up Call Buying Guide is no longer available, no other source
120 Winter 1999 50 Apothecary Cabinet Step 2: Mark the screw-hole centerpoints and mark and drill the slots on the sides (A)...
120 Winter 1999 52 Apothecary Cabinet Supplies: #8 x 1 1/4" pocket screws
120 Winter 1999 53 Apothecary Cabinet Carcase Exploded View: #8 x 1 1/4" pocket-hole screw; *Note: Mounting slots and mounting holes in A, B, and C must be drilled before assembly.
120 Winter 1999  Pattern Apothecary Cabinet Parts View, pocket holes: 1" from each edge not 1 1/2"
120 Winter 1999 Pattern Apothecary Cabinet Part A: 15 3/4 is from top edge to second mounting slot
120 Winter 1999 61 Portable Planers Photo of Jet JWP-12-4P shown in former blue color, tool now white and dropped the Shopline name. Unit still carried by JET.
120 Winter 1999 61 Portable Planers Chart, Makita, Comments: carbide knives are not available.
120 Winter 1999 62 Writing Desk For cutting diagram see Issue 124, June 2000, page 9, Talking Back
120 Winter 1999 63 Writing Desk The Drawer Unit Mounting detail: When the drop leaf panel (Q) is closed, its outside surface is flush with the sloped edge of the side panels (C).
120 Winter 1999 64, 66 Writing Desk Bill of Materials and Drawer illustration: Part N, length is 10 1/2" not 10 7/8"
120 Winter 1999 69 Photo Stand Exploded View: 2 acrylic panels needed; Tenon Detail, groove vertical to panel
120 Winter 1999 71 Air-Cleaning System Note: For access to the inside of the cabinet, replace the screws that fasten the side (E) on the pulley side of the blower with hanger bolts and wing nuts. Locate the switch or junction box in one of the other panels.
120 Winter 1999 73 Air-Cleaning System Buying guide, blower/motor: Grainger changed the motor to stock no. 7D554, 1,280-1,587 cfm, new phone no. 888-361-8649 Note: The blower cabinet and filter cabinet are based on the particular model we used. Measure your blower and filter before beginning construction to make sure they will fit in the cabinets dimensioned here. Cabinet sizes may need to be adjusted for other models of blowers and filters.
121 February 2000 4 Online Item shown in photo is the Dropleaf Workbench, plan DP-00057.
121 February 2000 31 Tips Sweatband keeps corded tools from going cordless: for safety attach Velcro to the sweatband and the mating piece to the cord with glue or tape. See Talking Back, Issue 125, August 2000, page 12.
121 February 2000 46 Nesting Tables Cutting Diagram in Talking Back, issue 124, June 2000, page 8.
121 February 2000 47 Nesting Tables

Exploded View, Medium Table: leg (A) width is 1 1/2"; part A 3/8" x 1 1/4" mortise 1" deep

121 February 2000 49 Nesting Tables Mortise Detail, right rear leg: 9/16", 3/8", 9/16". See Talking Back, Issue 127, October 2000, page 8.
121 February 2000 51 Cold Frame Bill of Materials: Part B, width should be 17 3/16". See Talking Back, Issue 124, June 2000, page 6.
121 February 2000 53 Traditional Rocker Effective 1/31/03 the full-size patterns are $10.95. Write to: Traditional Rocker, PO Box 349, Kalona, IA 52247
121 February 2000 55 Traditional Rocker Queen Anne Router Bit source: Infinity Cutting Tools, item 10-500, call 877-872-2487
122 March 2000 4 Online Plan shown is no. DP-00014
122 March 2000 25 Hot Off The Internet SAFETY NOTICE: Use caution when working with MEK and acetone. See Talking Back, Issue 126, September 2000, page 10.
122 March 2000 32 Ask WOOD Voltage: See Talking Back, Issue 126, September 2000, page 8.
122 March 2000 34 Hints for Huge Holes Safety Addition: see Talking Back 131, March 2001, page 10.
122 March 2000 57 Hall Table Cutting Diagram: Poplar piece is 3/4x5 1/2x72"
Cutting Diagram: Walnut, in order to achieve a continuous grain pattern across the front rails (C) and the drawer front (J), the parts should be cut in the sequence C-J-C. Flank the front rails with end rails (B). See Talking Back, 129, pg. 8.
122 March 2000 63 Gas Pump Clock Front View: 5 3/4" to bottom edge of part D.
122 March 2000 71 Router Tables Chart: Porter-Cable flatness rating is G. Woodhaven phone number is 319/785-0107. CMT's Industrio router-table available from Bench Dog, Inc., 800/786-8902.
122 March 2000 74 Dump Truck Tip for filing wheel-tread notches by hand see Talking Back, Feb 2001, page 12.
122 March 2000 75 Dump Truck Box illustration: Bottom edge of Part L is 4 1/2" not 6", see Box Parts View on page 124.
122 March 2000 85 Tray Tables Supplies: Roto Hinges available through Rockler and Woodworker's Hardware
122 March 2000 86 Tray Tables Tray Stand Exploded View: Part I measurement 13 1/4" between dadoes should be 11 3/4"
122 March 2000 87 Tray Tables FRONT LEG illustration, part I: Center of end hole 7/8" from end not 3/4". Part L 3/8" from end of I not 3/4".
123 April 2000 44 Shaker Tall Clock See Talking Back, Issue 127, October 2000, page 8, for finish we used on clock.
123 April 2000 52 Garden Shed Build the door header assembly, step 3: "Place it in the rabbet formed by parts J and L."
Bill of Materials: Part M, quantity 2; Part N, length 21 3/4".
123 April 2000 53 Garden Shed Exploded View: Total width of roof (parts Q and S) is 30" not 30 1/2"
123 April 2000 59 Plunge-Routing Basics Keyhole-Routing Jig: Length of router base plus 3 3/8". See Talking Back Issue 128, November 2000, page 10.
123 April 2000 62 All-Around Plunge-Router Jig Building to dimensions given in Bill of Materials results in a jig that fits a DeWalt router. To make the jig fit any other router, modify the ends (A, B) and fence rail (G). See Talking Back November 2000, page 8.
124 June 2000 16 Pocket-Hole Routing Jig 15° stock should be 3/4x2 5/8x9 5/8"
124 June 2000 81 Workshop Rest Stop (stool) Buying Guide change (7/08): Chrome-plated foot-rest ring is no longer available. Exploded View illustration: brass F.H. wood screw changed to F.H. wood screw. Supplies: flathead brass wood screws to flathead wood screws.
125 August 2000 26 Mini Router Table/Rotary Tools Carriage bolt is 5" not 4".
125 August 2000 42 Hand Plane Step 2, Cut five pieces of 1/4"-diameter brass rod to 2 5/16" long.
125 August 2000 43 Hand Plane Exploded View: 1/4" brass rod 2 5/16" long
125 August 2000 Pattern Double Settee See Issue 126, September 2000, page 10 for corrections to full-size patterns A & B.
125 August 2000 Pattern Double Settee Part T Full-Size Pattern mislabeled Support, is Front Seat Slat.
125 August 2000 Pattern Double Settee Part D Full-Size Pattern mislabeled Front Rail, is Armrest Support.
125 August 2000 72 Double Settee Bill of Materials: Part A width is 5 1/2" not 5 5/8".
125 August 2000 73 Double Settee Exploded View: Back of seats uses two screws per board, see page 72.
125 August 2000 78 Portable Sawmills Super Lumbermate 2000 replaced Norwood Industries model Mark IV, 126 Sept 2000,p.8
TimberKing update, 128, November 2000, p. 11.
126 September 2000 22 In Search of the Perfect Finish General Finishes phone number 262/786-6050
126 September 2000 50 Captivating Cupola Buying Guide: new address G.B.C. Millwork, 8151 Easton Road, Ottsville, PA 18942, phone 610/847-8100
126 September 2000 76 Pastry Stand Step 8: "and rout the top, then the bottom." Woodtek #819-487 bit 1/8" short, use Bosch 85467M bit.
127 October 2000 52 Segmented Bowls Here's the rule: corner 25° should be 45°.
127 October 2000 54 Sliding Table Add-On Delta 800/223-7278, in Canada 800/463-3582
127 October 2000 57 Sliding Table Add-On Buying Guide source is no longer available. No other sources available.
127 October 2000 67 Box-Joint Jig Exploded View and Step 4: "Make progressively deeper cuts until the cut in the assembly is 1" deep."
128 November 2000 68 Tablesaws Jet's fence-face material is made of high-density polyethylene (HDPE)
128 November 2000 68 Tablesaws Delta changed the model number of the 36-475 to model 36-477
128 November 2000 81 Empire State Express  Buying Guide, Hardware Kit is no longer available, no other source
129 December 2000 18 Router-Bit Review Step 3: "upper" cutting edge of the bit not "lower."
129 December 2000 96 Bandsaw Fence 3/8" all-thread rod 1" longer than A not 26 3/8" long
131 March 2001 53 Federal Bookcase Exploded View: spline is 36 7/8" long not 37 3/8". Delete "5/16" from top edge" for groove on part E.
131 March 2001 55 Federal Bookcase Buying Guide items no longer available from Constantine's. Shelf standards and supports are available at home centers. Finial available from Van Dyke's Restorers 800/558-1234, item no. AL-200123.
131 March 2001 64 Our country in quarters Pattern: 1 inch hole should be 1/16 inch deep
131 March 2001 64 Our country in quarters See issue 184, page 10, and 185, page 7, for additional pattern for District of Columbia and five US. Territories or http://www.woodmagazine.com/woodworking-tips/editorial-extras/ Brass plaque updated April 2010: cost is $7
131 March 2001 67 Our country in quarters Buying Guide, Plaque, update April 2010: brass plaque $7. Mail to WOOD Magazine Coin Map, 1716 Locust Street, LS221, Des Moines, IA 50309-3023.
131 March 2001 77 Stylish Storage Buying Guide: new address Constantines Wood Center, 954/561-1716 www.constantines.com
131 March 2001 77 Stylish Storage Buying Guide: new address Constantines Wood Center, 954/561-1716 www.constantines.com
132 April 2001 63 Built-In Bookcase Buying Guide: these Mission-style hinges are no longer manufactured - no other source found
132 April 2001 63 Built-In Bookcase Buying Guide: low-profile halogen lights new item no. 39739.
132 April 2001 86 Desert Dust Bin Pattern correction: see Talking Back, issue 134, August 2001, page 12. New pattern for cactus and row of lacing holes along one edge.
133 June 2001 16 Tool Buyers' Update Update: Craftsman 21713 depth-stop turret six different thicknesses (add 1/8")
133 June 2001 42 Garden Footbridge Rail: use 1 1/4" deck screws not 1 5/8" deck screws
133 June 2001 43 Garden Footbridge Step 5: change 1 5/8" deck screws to 1 1/4" deck screws
133 June 2001 43 Garden Footbridge Rail Holes: need 9 upright holes not 8. Correct hole measurements are 6 13/16" from centerline, 4 1/4" on center. Only end mounts (I) need the 15° bevel. See Talking Back, issue 141, April 2002, page 10.
133 June 2001 51 Racheting Candlestand Base drawing: Location of uprights F not B
133 June 2001 52 Racheting Candlestand Photo A is the wrong photo, caption is correct
133 June 2001 pattern Racheting Candlestand Upper Bolster: 9/16" along edge should be 5/8"
133 June 2001 61 Fishing Net Note: Count the number of loops on net bag and adjust the number and location of the loops holes. Supplier has no control over this situation. (see issue 140 page 10)
133 June 2001 74 Side-Draft Workbench Part QQ inside 3/4" rabbet 3/8" deep; outside 3/8" rabbet 3/8" deep
133 June 2001 76 Side-Draft Workbench (see Talking Back 139, p. 14)
Parts View: Part H switch cut out should be on other side; Part I 6 1/4" should be 6 3/4"; Part JJ clarification: optional 13/16" grooves 7/16" deep in top layer only
133 June 2001 77 Side-Draft Workbench Parts View: Part A, flip the drawing; Part E no cut out and center dado
133 June 2001 85 Two fast fixes for dust collection woes Bag part number changed to 145764
134 August 2001 14 Great Ideas: Fail-Safe Router Jig Clarity in setup instruction to get an exact-width dado: "then slip a scrap of shelf stock between the fixed and movable fences. Turn the wing nuts to snug the movable fence against the stock, and clamp it in place. Remove the scrap." Illustration: 1/4" washer should be 1/4" wing nut.
134 August 2001 40 Patio Party Center Drawing 5b Leaf Support: 8 1/4" and cutout moved to 9" width side of PP (see issue 139 p.10)
134 August 2001 57 Patina-Topped Jewelry Box Buying Guide: cork, feet, and hinges are no longer available. No other source available.
135 September 2001 8 Talking Back Update on Douglas fir: Textbook of Wood Technology states 38 pounds per cubic foot
135 September 2001 38 Sleigh Bed Bill of Materials and Exploded View: Part H length is 60 1/2" not 61 3/8".
135 September 2001 38 Sleigh Bed Cutting Diagram: D and E from 9 1/4" board not 7 1/4"
135 September 2001 38 Sleigh Bed Clarification: no round-over on inside face where F intersects D and F intersects E.
135 September 2001 38 Sleigh Bed Bill of Materials: part F, 1 3/8" thick
135 September 2001 38 Sleigh Bed Parts D and E are initially cut oversize, D is 8 1/8 and E is 7 3/8
135 September 2001 38 Sleigh Bed Vertical Raised-Panel Bit source: Infinity Cutting Tools, item 90-602, call 877-872-2487
135 September 2001 39 Sleigh Bed 5a Bed Rail Detail: mortise location 3/8", 5/8", 3/8" not 3/8", 5/8", 1/2"
135 September 2001 45 3-in-1 Work Support Drawing 1 Upright: Step 1, 1/2" arrow on right side point to side of 1" groove (like on left side); Second STEP 2 should be labeled STEP 3
135 September 2001 46 3-in-1 Work Support Hardware update: aluminum mini-track available from Rockler, rockler.com. 800-279-4441, part no. 34676
135 September 2001 58 Display Stand Step 3: Part E should be 3 3/4" not 3 1/2" from fence (see issue 140 page 8)
135 September 2001 59 Display Stand Illustration 4b: Part E should be 3 3/4" not 3 1/2" from edge (see issue 140 page 8)
135 September 2001 72 Storybook Lamp Exploded View: 7/32" hole 3/8" deep in 1" wood ball not 9/32".
136 October 2001 51 Custom Cabinetmaking VanDyke's Restorers no longer carries wood veneer tape
136 October 2001 75 Display Cabinet Supplies: Amerock 1" knobs BP-1590 no longer available, use knob of own choice
136 October 2001 75 Display Cabinet Buying Guide: Part no. 02S60 now 142852; available from www.woodcraft.com
136 October 2001 88 Drill Presses Chart: Jet amps should be 9/4.5 (see issue 140 page 10)
136 October 2001 93 Nighstand Buying Guide, drawer lock joint bits: price change to $54.99 as of September 2003
136 October 2001 93 Nighstand Buying Guide: Jesada drawer lock bit available from Razor Tools 877/898-6657
136 October 2001 99 Products That Perform SMartGRAIN printable veneer phone number changed to 641/533-2103
137 November 2001 38 Shop Tips Illustration: 1/4x3/8" splines should be 1/4x5/8" splines
137 November 2001 68 A Novel Box Change hardware buying guide: stop hinge, part no. 00D80.05, Lee Valley Tools 800-871-8158
137 November 2001 75 Armoire Buying Guide, drawer lock joint bits: price change to $54.99 as of September 2003
137 November 2001 75 Armoire Buying Guide, hardware: price change, no. 937-014, $2.99; no. 913-945, $6.89 as of Sept 2003
137 November 2001 90 Yuletide Container Buying Guide: Van Dyke's Restorers discontinued dye after article printing.
New Buying Guide: Woodworker's Supply, 800/645-9292, item W1790-Brilliant Scarlet
138 December 2001 44 Full-service benchtop router table Use T-track instead of T-slotted mini tracks and mini track
138 December 2001 45 Full-service benchtop router table Drawing 1: change mini-track to T-track; screws for T-track are #6x1/2 inch F.H. wood screws;change Round-knob to 3/4 inch stud not 1/2 inch stud
138 December 2001 46 Full-service benchtop router table Step 5: change mini-track to T-track
138 December 2001 46 Full-service benchtop router table Supplies: move 1/4 inch hexhead bolts from Buying Guide to Supplies list; add #6x1/2 inch F.H. wood screws
138 December 2001 46 Full-service benchtop router table Updated Buying Guide: Hardware. Knobs with 1/4 inch threaded inserts no. 27R14 (8); round knobs no. 27R11 (4), acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153. 36" T-track no. 12K79.24 (1); 24" T-track no. 12K79.22 (2); 2-1/2" vac port no. 03J61.10 (1). Lee Valley, 800-871-8158. Switch: Safety power switch no. 20915. Rockler, 800-279-4441.
138 December 2001 48 Full-service benchtop router table Drawing 3: change mini-track to T-track; step 3 change mini-track to T-track
138 December 2001 49 Full-service benchtop router table Step 2: change mini-track to T-track; Step 4 "See Buying Guide for our source of knobs."
138 December 2001 69 Arch-Topped Cabinet Clock Buying Guide correct part no.: Brass knobs no. 39500, $1.25 each; correct phone # Klockit 800/556-2548 (see issue 141 page 10)
138 December 2001 69 Arch-Topped Cabinet Clock Step 1: 3 1/4"-diameter hole for clock movement not 3 1/8"
138 December 2001 70 Arch-Topped Cabinet Clock 4 Front drawing: 3 1/4"-dia. Hole not 3 1/8"
138 December 2001 Pattern Tabletop Reindeer Narrow Leg made out of 1/8" stock not 1/2" stock; wedge 3/8" stock
138 December 2001 79 Eight-drawer dresser Buying Guide, drawer lock joint bits: price change to $54.99 as of September 2003
138 December 2001 79 Eight-drawer dresser Buying Guide: Jesada bits available from Razor Tools 877/898-6657
138 December 2001 82 Suite Reflections (mirror) Buying Guide: Change call Jesada to call Razor Tools at 877/898-6657
139 February 2002 41 Futon Buying Guide price change: part no. 953-817 $10.99 as of September 2003
139 February 2002 44 Eye-Catching Coasters See modified corner-cutting jig in issue 143, September 2002, page 8.
139 February 2002 51 Space-Saving Work Center Supplies: Change source for optional Quick-Vise to Irwin Industrial Tools, same phone number (vise model changed from one in photo)
140 March 2002 58 Desk Illustration 5a: 4 1/2" should be 5 1/4" for magnetic catch
140 March 2002 60 Desk Organizer Materials List: part C length is 5" not 4 1/2"
140 March 2002 79 Retro TV Desk Clock Exploded View, Part A: 2 3/8" hole 3/4" deep
140 March 2002 95 Showtime Storage Side Panel Full-Size Detail Pattern: 1/2" rabbet 1/4" deep on inside face not ouside face
141 April 2002 49 Stand that delivers (media stand) Buying Guide, new address: Glass & Mirror Craft Industries, Inc., 48230 West Road, Wixom, MI 48393
141 April 2002 65 Pergola Cutting Diagram: notches for end girders (H) go on top not bottom, see drawing 3
142 June/July 2002 22 Shop Tips Telephone number Goldblat 800/782-6539
142 June/July 2002 22 Shop Tips Telephone number Goldblat 800/782-6539
142 June/July 2002 61 Grand entrance (gate) Drawing 6 and Step 4, Part R: Lay part R diagonally across the assembly with the top end opposite the hinge side.
142 June/July 2002 63 Grand entrance (gate) Buying Guide: HardieSingle Individual Shingles, web site www.jameshardie.com
143 September 2002 50 Lazy-days chaise Buying Guide, Cushion: Manufacturer is out of business. Cushions are available at local seasonal furniture stores.
143 September 2002 59 Knockdown Cabinet System Double Base and Top Cutting Diagram: top and second board changed to top board: move J's to second board second board: 2 needed, remove one set of H's and add two J's from top board
143 September 2002 59 Knockdown Cabinet System Double Base and Top Cutting Diagram: top and second board changed to top board: move J's to second board second board: 2 needed, remove one set of H's and add two J's from top board
143 September 2002 59 Knockdown Cabinet System Double Base and Top Cutting Diagram: top and second board changed to top board: move J's to second board second board: 2 needed, remove one set of H's and add two J's from top board
143 September 2002 60 Knockdown Cabinet System Materials List: I's and J should be quantity 4 Single Base and Top Cutting Diagram: board with I's and J's, 2 are needed
144 October 2002 18 Salt & Pepper Shakers Buying Guide: the bungs listed are item #123-0148, $.99 each (see issue 147 page 11)
145 November 2002 70 Pendulum Cradle The 3/4" dowels that the cradle swings on are correctly sized at 1 1/4" long. These dowels are glued into the ends (A) in Step 1 under "Assemble the cradle" on page 72. The 1 1/2"-long dowels specified in Step 8 on page 73 are used temporarily to align the spacers (D) with the supports (E) during glue-up. The extra 1/4" allows you to pull the dowels back out of the hole after the glue dries.
146 December 2002 64 Oil-candle trio Buying Guide: Teardrop oil candles have been pulled from the market for safety concerns, item no longer available.
146 December 2002 74 Two-In-One Arts & Crafts Chair Rocker Form, drawing 7, middle-dimension should be 7 7/8" not 8 1/2"
147 March 2003 51 Baker's Trio Step 4 and bottom photo caption: 1/8" BIRCH dowel not walnut (see 149 page 6)
147 March 2003 56 Baker's Trio Supplies: 1/8" BIRCH dowel not walnut
147 March 2003 78 Country Furniture in the making Web site address is http://woodstore.woodmall.com/counfur.html
147 March 2003 86 Resawing Page reference to page 87 should be to page 84
148 May 2003 cover Dovetail Secrets heading on page 86 and 90
148 May 2003 29 Shop Tip A press for gluing stacked bowl blanks The compression nut (veneer-press screw) should be below the bridge
148 May 2003 31 Shop Tip: Rout parallel slots to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
148 May 2003 44 Onlay Accents Made Easy Photo labels missing. Top photo C, bottom left A, bottom right B.
148  May 2003 62 Arts & Crafts Table Lamp Lamp kit price $54.95 plus shipping; Lumber kit no longer available.
148 May 2003 66-67 Candle Laterns Glass dimension should be 3 9/16" wide not 3 11/16" wide (referenced in Note, Exploded View, and Supplies) (see issue 151 page 6)
148 May 2003 73 10 Portable Planers Chart Note #5: page xx should be page 71
148 May 2003 96 Patio-Perfect Planter Materials List: Part A width is 17 1/8 and length is 16 3/8"
149 June/July 2003 55 Bandsaw table system Buying Guide Kits are no longer available (March 2008)
149 June/July 2003 65 Accessories for Bandsaw Tapering Jig: 3/4" counterbore 1/4" deep not 1/2" counterbore
149 June/July 2003 66 Accessories for Bandsaw Buying Guide Kits are no longer available (March 2008)
149 June/July 2003 79 Adirondack Chair & Footrest Materials List: part M width is 2 1/2" not 2 5/16" (6 slats not 7 as shown in photo p. 74) (see issue 152 page 6)
150 September 2003 55 Occasional table Scrapwood router trammel: Reverse arrow on routing direction towards top of the circle
150 September 2003 86 Pizza Peel See issue 152 page 6 for full-size handle end pattern

 

Issues 151 to current
WOOD MAGAZINE CHANGES / UPDATES Issue 151-present
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
151 October 2003 57 Tough-Stuff Workbench Update Buying Guide, Cabinets: Can also use 28" full-extension drawer slides no. 02K30.28
151 October 2003 77 Cabinet-Style Tablesaw Delta 36-L31X-U50 $1,750 (see issue 153 page 10)
151 October 2003 84 Dead-on 90 degree crosscut sled Drawing 3: guide bar change to 3/8x1/2x1-1/4 inch; Stopblock change to 3/8 inch dado 1/4 inch deep 7/8 inch from top edge; washer is 1/4 inch flat washer
151 October 2003 85 Tableaw Jigs Buying Guide Update: Hold-down with bolt and knob no. changed to 145831
151 October 2003 92 High-Class Collector's Cabinet Buying Guide: shelf supports part number is G611WPB
151 October 2003 95 Temps in a tube READ important information that comes with the Galileo thermometer before cutting parts Part D: cut length to suit thermometer; Part B: diameter may vary (see issue 153 page 10)
151 October 2003 95 Temps in a tube Buying Guide is no longer available. Refer to Amazon.com for Galileo thermometers of various sizes.
152 November 2003 62 Pocket-Hole Jigs Paragraph: Several jigs are adjustable to increase the spacing for wider workpieces, but only two—the Task Pro Center 06250 and Kreg K2000 (NOT K2)—can go narrower.
152 November 2003 64-65 Pocket-Hole Jigs (chart) The Kreg ProPack includes the Mini, Rocket, and K2000 jigs. Hole spacing on the K2 model is 7/8". Spacing on the K2000 is 9/16, 7/8, and 1 7/16".
152 November 2003 90 Super-Flexible Shop Storage Drawing 9: 5 1/2" measurements between bins should be 4 1/4"; Photo A and caption 4 1/4"-wide spacer; page 91, step 3, 4 1/4"-wide spacers.
See Sounding Board, issue 156, June/July 2004, page 10.
152 November 2003 91 Super-Flexible Shop Storage Hardware update: plastic sliding door track, no. 10007, shelf pins, no. 22773, available from Rockler, rockler.com. 800-279-4441
153 December 2003 52 Slant-Front Secretary Drawing 2: 1 3/16" for placement of centered screws for inside part D should be 1 9/16"
153 December 2003 55 Slant-Front Secretary

Missing dimension: Part N top edge is 10 3/4" on drawing 5. See issue 155, page 12.

153 December 2003 98-99 Cyclone Dust-Collectors Additional information see issue 155, page 12.
153 December 2003 108 Crown-Molding Shelf Note: standard crown molding (38°); miter angle = 31.6; bevel angle = 33.9
153 December 2003 122 Pyramid Point Tool Photo B incorrect, see issue 155, page 12, for correct photo
154 March 2004 55 The Shelf Maker's Complete Guide Adjustable support options: Low-profile shelf standard is shown in photo but not labeled, used with low-profile support labeled as before and after insertion.
154 March 2004 65 Shelf-top weather station Sources: Instruments are no longer available
154 March 2004 93 CD storage Sources, CD Racks: Rockler is no longer sourcing pop-out CD racks no. 35875. No other supplier located.
154 March 2004 96 Cat's Meow Scrollsawn Plaque Exploded View, Drawing 1: 2 3/8" should be 2 3/16". See Sounding Board, issue 156, p. 10.
155 May 2004 37 Easy Glider Drawing 5 Seat Support Cover: part M length should be 15 11/16"
155 May 2004 40 Easy Glider Materials List: part M length should be 15 11/16"
155 May 2004 pattern Easy Glider Pattern for part M length should be 15 11/16"
155  May 2004 51 Torpedo Level Level kit: Price $12.50 plus shipping
155  May 2004 73 Traditional Sideboard Sources Hardware kit for sideboard: Part no. 02K14.17 changed to 02K40.17; Kit no. 05D15.15 is no longer available. Hardware kit for optional center door: Kit no. 05D15.16 is no longer available.
155  May 2004 82 Kid's room ensemble Sources: Cork source is no longer available. For cork go to art and craft supply stores. For 3M Super77 Multipurpose Adhesive go to hardware store and home centers.
155  May 2004 90 Make a splash with a "waterfall" joint Fence should be on the side that is away from direction of blade tilt.
156 June/July 2004 28 Epoxy Goes Mainstream see issue 160, page 12, for glove information
156 June/July 2004 46 Heirloom tall clock Sources: Mechanical clock movement/hardware is no longer available. Quartz clock movement/hardware kit is still available.
156 June/July 2004 53 Drill Press Table Drawing 1: Part E is 6 x 8 3/4"
156 June/July 2004 56 Drill Press Table Sources Hardware Kit: Call for current prices.
156 June/July 2004 79 Benchtop Mortisers  Chart: 200 listed twice on thermometer, temperature shown is correct
156 June/July 2004 87 Four-Jaw Chucks Coming in issue 160 not 159
156 June/July 2004 88 Rugged "n' Ready Tool Storage Tag-along tool tote: plans in issue 158, October 2004
156 June/July 2004 95 Wind Chimes Source, chime kit, is no longer available.
157 September 2004 40 Easy-Lock Featherboard Note: Feather board to be used on tablesaw WITH T-style miter-gauge slot.
157 September 2004 49 Tower Cabinet Drawing 1: H is 15" from top of B. See issue 161, page 12.
157 September 2004 50 Tower Cabinet Step 1: …outside corner of each foot. Adjust your biscuit joiner to cut slots for #0 biscuits in the legs where shown on the patterns and Drawings 8 and 8a. Then adjust the biscuit joiner to center the slots in the legs in the 3/4" thickness of the rails and cut slots where shown on Drawing 8. See issue 161, page 12.
157 September 2004 51 Tower Cabinet Drawing 8a: biscuit slot center is 5/8" from edge not 3/4". See issue 161, page 12.
157 September 2004 52 Tower Cabinet Step 1: Then raise the blade to 1 5/8"; drawing 10: 1/4" groove 1 5/8" deep, centered. See issue 161 p.12.
157 September 2004 57 TV stand/coffee table Drawing 3 and 3a: see change for page 50. See issue 161, page 12.
157 September 2004 68 End Tablet Drawing 3a: see change for page 50. See issue 161, page 12.
157 September 2004 85 Woodworking Glues Heat resistance: All of the joints made with Elmer's Carpenter's Exterior outlasted the wood.
157 September 2004 117 Shop-Proven Products Avenger Products phone number changed to 702/293-7510 (see issue 160, page 10)
159 November 2004 46 Do-It-All Router-Table Fence Buying Guide: Wood kit is no longer available. Material available at home centers.
159 November 2004  51 Salad Bowls Sources Lathe Chuck. Part C3418 upgraded to CUG3418 $79.95
159 November 2004 70 Multi-base router kits See issue 161, page 12: The plunge base of the Porter-Cable plunge router 895PK does come standard with dust collection
159 November 2004 72 Multi-base router kits See issue 161, page 12: Under "Low points," the first point should read "The auto-engaging spindle lock doesn't work with the optional dust shroud…" Note, however, that the spindle lock can be operated manually.
159 November 2004 80 4 must-have jigs from 3 router experts Vertical stock pushstick: 30 degree bevel on handle not 45 degree (see issue 161, page 12)
159 November 2004  89 How to choose a router table See issue 161, pager 12: The model for the MLCS cast-iron router table should read #9593.
160 Dec/Jan
04/05
18 Four-Jaw chucks Update: Penn State C3418 is now CUG3418, $79.95. See issue 162, page 8.
160 Dec/Jan
04/05
70-74 Shaker Clock Source: Clock kit: Radio-controlled clock movement no longer available. Replaced with quartz clock movement. Order kit no. SK-WAL-Q for walnut or kit no. SK-CH-Q for cherry.
160 Dec/Jan
04/05
71, 74 Shaker Clock Source: Spalted maple blank no longer available.
160 Dec/Jan
04/05
87 Photo Frames With a planer photo: the 1/2" is from the bottom not to top edge (see Planer Beveling Jig drawing)
160 Dec/Jan
04/05
68 Arts & Crafts Dresser Drawing 7: Part LL 8 3/4" from outside edges should be 7 1/4". See issue 163, page 8.
161 Feb/Mar
2005
24 Create Super-Strong Bridle Joints Tall Stock Pushblock: 45° change to 30°. See issue 163, page 8.
161 Feb/Mar
2005
46 Closet Storage System Step 1, caption: Position the base 2 1/4" from back wall.
161 Feb/Mar
2005
71 14.4-volt drills Trustworthy Torque Specs chart: Bosch 32614 is 300; Bosch 33614 is 450. See issue 163, page 8.
162 Apr/May
2005
38 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
162 Apr/May
2005
39 Mitersaw Work Station Drawing 2, BASE and Materials List: J is 14-3/4 inches not 14 inches; Key 3-1/2 inches is 3-1/4 inches.
162 Apr/May
2005
41 Wall Cabinet Drawing 4: Shelf holes start 7" inches from top not 7-1/4 inches from top of part A.
162 Apr/May
2005
70 Utility Cabinet System Photo E and caption: spacer is 21" long
162 Apr/May
2005
81 Brad Nailers Chart: Porter-Cable BN200A fastener lengths 3/4-2 inches
162 Apr/May
2005
106 Shop-Proven Products Rockler Woodworking and Hardware 800/279-4441
163 Jun/July
2005
30 Shop Tip: Feather boards The feather board's pressure should end just in front of the teeth of the blade. See issue 165, page 8.
163 Jun/July
2005
46 Sliding-door cupboard 5b Corner Block: top notch is 1 3/8" (same as bottom notch). See issue 165, page 8.
163 Jun/July
2005
62 6 ways to beef up a workbench Tool Totes and Case: Front cleat D 1 1/2" from front edge of top (A).
163 Jun/July
2005
70 Bathroom Cabinet Drawing 4 Door: Horizontal bead K 5/16" thick
163 Jun/July
2005
70 Bathroom Cabinet Drawing 4 Door, mirror: Measurement for mirror 1/8x11-7/8x21-1/8"
163 Jun/July
2005
80 Mid-priced tablesaws Rigid TS2400 phone number 800/474-3443
163 Jun/July
2005
81 Mid-priced tablesaws Web site for In-line Industries is in-lineindustries.com
164 September
2005
41 Salt & Pepper Mills For correct full-size cap and base template go to issue 166 page 58
164 September
2005
76 Monster Routers Chart: Smartlift Digital bits can be changed above table with this lift, the chart should show a large bit instead of the X. See issue 166, page 8.
164 September
2005
77 Monster Routers Porter-Cable DOES offer optional below-the-base dust-collection accessories. See issue 166, page 8.
164 September
2005
78 Monster Routers Porter-Cable 7518 and 7539 DOES offer optional below-the-base dust collection accessories. See issue 166, page 8.
164 September
2005
79 Monster Routers Chart: Accessories (11) Optional for Porter-Cable 7518: B,E,G,Q; Porter Cable 7539: B,E,G,K,Q
165 October
2005
50 Compact entertainment center Source: Rockler no longer sources the #8-32x5/8" knob hanger bolts, they are available at hardware stores
165 October
2005
53 Dead-blow mallet Photo B: The piece being routed is held away from the bit (not as shown in photo)
165 October
2005
62 Stop tear-out while drilling, routing, sawing Caption for 1b: Align the chuck with progressively harder taps against its lower portion using a piece of scrap and hammer. See issue 167, page 8.
165 October
2005
68 A gem of a jewelry box Shop Tip photo: Groove only in middle of drawer side (ignore groove shown on edge of side).
165 October
2005
72 Clamp-on Tool Guides Chart: Converter Router Trolley model is sold with a pair of 48" rails. See issue 167, page 8.
165 October
2005
82 4 easy bookcase options Option 4: Van Dyke's Maple is 02036147 and Oak is 02022067
166 November 2005 62 Curio Shelf and Hall Table When using one of the alternate joinery methods, cut the four aprons (B,C) 1 1/2" shorter than specified in the plans. (Cutting off the tenons.) Be sure to cut to length before laying out the arc. All other measurements and steps remain the same. See issue 171, page 8.
166 November 2005 92 Shop-Proven Products: Freud Box Joint Cutter Set (SB0X8) The photos of the 1/4" stack and 3/8" stack blades are reversed.
167 Dec/Jan 2005/2006 32 Shop Tips Source for magnetic base: Woodcraft item no. 128398. Call 800/225-1153 or visit woodcraft.com
167 Dec/Jan 2005/2006 85 Photo Display Stand Exploded View: #6-32 machine screw should be 1 1/2" long. See issue 169, page 12.
167 Dec/Jan 2005/2006 86 Photo Display Stand Supplies: #6-32x2" roundhead machine screws. See issue 169, page 12.
167 Dec/Jan 2005/2006 86 Photo Display Stand Step 2: Hacksaw two #6-32x2" roundhead machine screws to 1 1/2" long, removing the heads.
168 Feb/Mar 2006 14 Tool Shop: Jointers Photo, lower left: Labels for infeed and outfeed table are switched. See issue 170, page 10.
168 Feb/Mar 2006 55 4 Tablesaw Jigs Drawing 1, Box-Joint Sled: The width of the blade guard and acrylic on the box-joint sled is 3-1/4" wide to allow for the rotating of the four-arm knobs. The adjusted slot length is 3/4" and location is 3-3/8" from outside edge of fence. See issue 170, page 10.
168 Feb/Mar 2006 57 4 Tablesaw Jigs Drawing 4a: center of pilot hole is 7/8" from left edge, not 1/2" as shown, and centered 1/2" from top edge; lower dimensions are 1/8" and 3/4". See issue 170, page 10.
168 Feb/Mar 2006 58 4 Tablesaw Jigs Drawing 2: missing dimension on Adjustable Stopblock, lower right, is 1/2" from edge.
168 Feb/Mar 2006 67 How to cut tails-first dovetails See issue 169 WOOD Patterns insert for pattern
168 Feb/Mar 2006 73 8" Jointers We tested the Powermatic PJ-882 (no. 1610079), price $1,650. See issue 169, page 12.
168 Feb/Mar 2006 74-75 8" Jointers Chart: We tested the Powermatic PJ-882 (no. 1610079), price $1,650. See issue 169, page 12.
168 Feb/Mar 2006 82 Mantel Clock Part labels D and P on clock face of Exploded View are not needed
169 April/May 2006 58 Planter Box Drawing 2c: Missing dimensions on top edge (right and left side ) are 1" trim to fit during installation; 2" from edge to beginning of curve; 32" for finished length. See issue 172, page 10.
169 April/May 2006 64 Beating the elements See 172, page 10 for update.
170 June/July 2006 86, 88 When good wood goes bad Illustration on page 87 for plainsawn is correct. The illustrations for cupping on pages 86 and 88 show the incorrect grain.
170 June/July 2006 95 Build-A-Gift Contest An entry must fit into a 2x2x3 foot box (61x61x91 cm)
171 September 2006 20 Shop Tips: Steady-as-she-goes biscuit joiner jig Handhold: 1 inchradius not 2 inch radius; 3/4 inch radius not 1-1/2 inch radius
171 September 2006 34 Self-sizing dado guides Accurate Guide is no longer available
171 September 2006 41 Heirloom bookcase Plunge the biscuit slots in the front legs (F) before gluing the side edging (G) to them. Referred to in the following text: Step 4: …plunge a slot in the inside face of each leg at the marked centerline, as shown in Photo H .Step 2: Then glue and clamp an edging piece to the inside face of each front leg (F), flush with the top and back, where shown on Drawings 2 and 2b. See issue 177, page 8.
171 September 2006 62,64 Regal Eagle Source: Pneumatic sanding drum and adapter are no longer available. An oscillating spindle sander or sanding drum on drill press will also work.
172 October 2006 16 Ask WOOD One good turn: Rockler no longer carries the Quik-Crank bandsaw tensioner. Contact Highland Hardware, part no. 086085, 800/241-6748 or tools-for-woodworking.com
172 October 2006 100 Shop-Proven Products VersaClamp: Mounting brackets are included in the $35 price. Additional brackets can be purchased for $5 per pair. See isue 175, page 12.
172 October 2006 104 Shop-Proven Products Dust Deputy: Contact information missing. Oneida Air Systems, 800/732-4065; oneida-air.com See issue 175, page 12.
173 November 2006 13 Fibonacci gauge Source: Locktite should be Loc-Tite
173 November 2006 44 3-in-1 bed for all ages Toddler bed photo: Front legs should have only one hole and bolt, on the inside edge of the leg, not as shown in photo. Instructions are correct.
173 November 2006 51 3-in-1 bed for all ages Assemble the crib, step 1: …connector bolts through the bottom inside holes in the headboard legs (A)….
173 November 2006 54 3-in-1 bed for all ages Source: Hardware Kit. …cross dowels (12) not (8)
173 November 2006 78 Planers Update: DeWalt DW735 price $550
174 Dec/Jan 2006/2007 39 Heirloom corner cabinet Drawing 1b: Counterbore for fastener is on the inside face of parts A,B, K,L,M
174 Dec/Jan 2006/2007 80 Wedged-tenon bench For more on forming the mortises, see page 94 not page 104.
174 Dec/Jan 2006/2007 82 23 tableaw tips, tricks, and techniques See issue 177, page 8. It's okay to use miter gauge and rip fence together when making partial-depth cuts for dadoes, rabbets, or tenons.
174 Dec/Jan 2006/2007 82 23 tableaw tips, tricks, and techniques See issue 177, page 8. Step 1: first attach the temporary hardboard tabletop to the saw's tabletop, then raise the blade through it, then set the distance from the rip fence.
174 Dec/Jan 2006/2007 84 23 tableaw tips, tricks, and techniques Step 9: You'll find plans for this outfeed table at woodmagazine.com/outfeedtable
174 Dec/Jan 2006/2007 85 23 tableaw tips, tricks, and techniques Step 15, update: Taper jig runs in the miter gauge slot.
175 March 2007 50 Give a top a whirl (turned top) Due to back orders until May 2007, an alternate source for top hardware is LeeValley, kit no. 88K81.51 and mandrel no. 88K81.52. LeeValley 800/871-8158 or leevalley.com
175 March 2007 68-71 a cut-above mitersaw platform The galvanized pipe is 1 inch O.D. and 3/4 inch I.D.
176 May 2007 64 Tug-along caterpillar Cut the round segments, photo 2: Caption should read Round segment not Wheel segment
176 May 2007 65 Tug-along caterpillar Form the wheel segments, photo 1: Caption should read Round segment not Wheel segment
176 May 2007 73 Picture frames Drawing 2 Spline-Cutting Sled: 1/8" slot should be 1/2" deep not 3/4" deep
177 July 2007 20 Smart Ways to Store WOOD magazine Drawing for Binder Jig: Base board 10 7/8" goes the length between the 3/4" end pieces.
177 July 2007 39 Table Lamp Photo top right-hand corner: 1/8" diameter should be 1 1/8" diameter
177 July 2007 42 Table Lamp Wiring Detail: Gold-colored wire should wrap clockwise
177 July 2007 45 Trim Routers The bit opening on the Porter-Cable 310 subbase should be 1-3/16", as listed in the chart on page 46.
177 July 2007 46 Trim Routers Grizzly does not offer optional bases for its model H7791 trim router.
177 July 2007 76 Gum Ball Goose Step 5: Sand the tail (B) to 11/16" thick
178 September 2007 44 Heirloom cradle Sources, Mattress: Custom mattress size is 12x28"
178 September 2007 47 Tablesaw Workbench Source: Casters no. 00K21.41, Lee Valley Tools, leevalley.com, 800-871-8158
178 September 2007 48 Tablesaw Workbench Drawing 2: locking swivel caster not double-locking swivel caster
178 September 2007 98 Clamp down on glue-up mistakes Update to Tip #2: You should wipe off glue squeeze-out while it's wet. See issue 181, page 8.
178 September 2007 110 Miter-joint slippage The MLCS Merle band clamp (part #9012, 800-533-9298 or mlcswoodworking.com) uses a 23" steel band rather than fabric
179 October 2007 13 Shop Tips: Where's that pencil? Safety alert: It's best to avoid using a lanyard with pencils.
179 October 2007 33 Bench-tool System Project Highlights, item 4: Locking casters not dual-locking casters
179 October 2007 35 Bench-tool System Drawing 4: Locking swivel casters not dual-locking swivel caster
179 October 2007 36 Bench-tool System Drawing 5: 4" locking swivel caster not dual-locking swivel caster; Source: Casters, 4" locking swivel plate casters no 00K21.41. Lee Valley Tools, leevalley.com, 800-871-8158.
179 October 2007 58 Plane-fun kid's shelf Photo shows part P reverse of drawings. Part P can be attached either way.
181 December/January
2007/2008
24 Rule-joint
Router Bits
Photo D: Shoulder is 5/32 inch not
3/32 inch
181 December/January
2007/2008
40 Modular Cabinets Source, hardware: Part no. HB28C25 changed to THB0144.
181 December/January 2007/2008 42 General-Purpose Tablesaw Blades Saw blade retest: See issue 183, May 2008, page 44
181 December/January 2007/2008 62 Drop-Leaf Table Sources, hardware: Rockler classic pull-out leaf support no. 29512 discontinued, substitute with metal drop leaf support no. 30006
182 March 2008 17 Shop Tips: Lucy, you've got some splinin' to do Aluminum plate: make as two triangles that meet at the points
182 March 2008 18 3-way mitered half-laps Heading should be Mitered half-laps
182 March 2008 34 A perfect puzzler: Caged dove Drawing 2b Drawer Detail Step 3: Part D 5/16 inch hole is 3/8 inch from back edge; Part C 5/16 hole is 1/2 inch from back edge.
182 March 2008 35 A perfect puzzler: Caged dove Make the drawer,, Step 4: Drawer C, drill a hole centered 1/2 inch from the back edge; Filler D, bore hole centered 3/8 inch from the back edge.
182 March 2008 84 Ribbon clock Photo A: Pattern in photo incorrect, follow pattern on page 56
184 July 2008 10 Sounding Board April 2010, update to brass plaque: cost $7. Coin holder dimensions see issue 185 page 7 and http://www.woodmagazine.com/woodworking-tips/editorial-extras/
184 July 2008 16 Shop Tips: Quick-set gauge for honing guide Acrylic is 1/4 inch thick
184 July 2008 44 Scrollsawn Safari puzzle We inadvertently omitted the full-size patterns for the zebra and rhino from the pattern insert. For the patterns go to http://www.woodmagazine.com/woodworking-tips/editorial-extras/
184 July 2008 49 Our 20 best router tips and tricks Tip 8: Hole slightly larger than the diameter of the 1/2" cove bit
184 July 2008 69 Keys to Successful Hand-Sanding Sources: Correct Flex-Hand Pad/H&L part number is #FR22150
185 September 2008 38 Showplace Cabinet Source hardware: Change cushioned shelf supports to part no. G708WBN
185 September 2008 72 Contractor-Grade Mobile Crane Drawing 5a: two holes used to attach hoist sides to mast assembly are 3/16 inches
186 October 2008 64-65 Quilt Ladder Hardware, Rockler: barbed threaded insert, no. 32025, is no longer available. Replace with hex drive threaded insert, no. 31872. Ready the rungs, step 2, using the hex drive threaded insert, no. 31872, drill a 3/8" hole 7/8" deep at each center mark for inserts. Change Drawing 2 and 2a holes to 3/8" hole 7/8" deep for hex drive threaded inserts. Ssee issue 189, page 6.
187 November 2008 61 Bow-Front Display Case Materials List, part E: Width should be 3-1/2"
188 December/January 2008/2009 74 Ask WOOD: Splitter or riving knife Underwriters Laboratories (UL) has moved up the date for manufacturers to comply with its tablesaw riving-knife requirement. As a result, all tablesaws manufactured after Jan. 31, 2010 must include a riving knife in order to get UL approval.
189 March 2009 14 Shop Tips: A slick trick for routing perfect hinge mortises The spacer must equal the length of the hinge minus the diameter of the bit, in this case a 1/4" spiral bit.
188 December/January 2008/2009 74 Ask WOOD: Splitter or riving knife Underwriters Laboratories (UL) has moved up the date for manufacturers to comply with its tablesaw riving-knife requirement. As a result, all tablesaws manufactured after Jan. 31, 2010 must include a riving knife in order to get UL approval.
189 March 2009 14 Shop Tips: A slick trick for routing perfect hinge mortises The spacer must equal the length of the hinge minus the diameter of the bit, in this case a 1/4" spiral bit.
189 March 2009 53 Wall Organizer Materials List. Change part F quantity to 1.
191 July 2009 22 Make Router Burn Marks Disappear See related video at woodmagazine.com/routerburns
192 September 2009 15 Shop Tips: Multi-tasking tablesaw sled 14 inch dimension on back end of sled should be 10 inches
194 November 2009 32 Blanket Chest Drawing 1 and 1a: width dimension for part A is 16-1/8"
194 November 2009 36 Blanket Chest Materials Lists: width of part A front/back is 16-1/8"
194 November 2009 38 Dovetailing Wide Panels Change: Clamp the test boards to opposite sides of the spacer block, with their outside face facing out, and tight to the underside of the template [Photo A].
194 November 2009 48 Blanket Chest pattern Traditional American Blanket Chest Base Full-Size End Pattern: pattern is too short. Pattern should be 4" not 3-3/4" tall.
195 Dec./Jan. 2009/2010 50 Chip & Dip Tray Templates for success, step 1: Template pieces should be 1/2x11x19"
195 Dec./Jan. 2009/2010 55 11 ways to get the most from your plunge router Mortising/Doweling Jig: the screw holes used to mount the aluminum bars to the wood guides must be countersunk into the bars to sit flush below the surface of the acrylic top. See issue 198, July 2010, page 6, for updated illustration.
196 March 2010 67 Cook up a kitchen makeover in your shop Sources, Clear finish: Old Masters web site changed to oldmasters.biz
196 March 2010 77 Ask WOOD: The splashy waterfall joint Fence should be on the side that is away from direction of blade tilt.
197 May 2010 22 Add storage to stands Drawing 3: wire pull screw goes through parts J and K; part I width is 10-1/2"
197 May 2010 24 Add storage to stands There is an error in Section 2 of customizing your own stand. For Step B, the difference in our example should be 1-1/4". As a result, the new length in Step D would be 11-3/4". Materials List: Part D width=16-1/2" and length=26-1/2"; Part E width=16-3/4" and length=12"; Part I width=10-1/2".
197 May 2010 54 3-hp tablesaws SawStop High Points: Hose support, mounting hardware, and 1-1/4" hose are an optional kit. These items do not come with the saw.
197 May 2010 74 Media Cabinet Step 1: See the Quick and Easy jig on page 16 not page 18.
198 July 2010 8 Shop Tips Rockler's phone is 800-279-4441
198 July 2010 57 Hall tree storage bench Materials List: Part F lower divider, length is 14" not 14-3/4"
198 July 2010 70 Drill- and router-bit case Cutting Diagram: Part C perforated hardboard is 3/16x24x48"
199 September 2010 66 Dust-catching sanding center More Resources: Reliably Rugged Assembly Table is at woodmagazine.com/assemblytable
200 October 2010 43 Organize Your Shop in a Weekend Garage dimensions are 14x24'
201 November 2010 32 Drop-Down Battery Dispenser For the updated plan, go to http://www.woodmagazine.com/woodworking-plans/shop-organization/battery-dispenser/ or refer to Sounding Board, issue 205, July 2011, page 6.
201 November 2010 41 Greene & Greene-style Clock Drawing 1, Side Assembly: on part B 1/8" groove 3/8" deep 1/8" from back face; on part C 1/8" groove 1/8" deep, 1/8" from back face
201 November 2010 78 Shop-Proven Products: Colt drill bits Go to Colt Web site (colt-tools.com) to find a full list of retailers.
202 Dec/Jan 2010/2011 53 Gumball machine Drawing 1, Exploded View: 3/4" I.D. copper cap. See Sounding Board, issue 205, July 2011, page 6.
202 Dec/Jan 2010/2011 62 Luminous Display Pedestal Wiring update: See Sounding Board issue 202, December/January 2010/2011, page 6.
202 Dec/Jan 2010/2011 79 Ask WOOD: Birdhouse basics More tips for building better birdhouses, see issue 205, July 2011, page 7
203 March 2011 28 Pocket-Hole Jig Organizer & Base Organizer and base was designed to fit a Kreg K3 jig. See Sounding Board, issue 208, November 2011, page 6.
204 May 2011 20 Mitered Half-Laps Drawing 2 Stile Routing Jig: remove mention "Half of frame width." Build the mitered half-lap jig using the width of the frame as the length of fence reach beyond the base, see Sounding Board issue 206, page 8.
204 May 2011 58 Step-by-Step Elegant Chair Drawing 2, Front Leg: 1-5/8 inches of leg width should be 1-7/16 inches
204 May 2011 60 Step-by-Step Elegant Chair Drawing 4, Shoe: Top left-hand measurment of 2-3/4 inches should be 2-1/2 inches
204 May 2011 61 Step-by-Step Elegant Chair Drawing 5, Crest Rail, part D: Bottom left-hand measurement from beginning line to first spoke mortise of 2-3/4 inches should be 2-1/2 inches
205 July 2011 29 Glider Drawing 1, Leg: dimension for carriage bolt location is 11 inches from bottom of Leg (A). See Sounding Board issue 206 page 8.
205 July 2011 46 Scrollsawn Potpourri Box The pattern for the left-most box lid on page 46 was printed too large. To correctly size the pattern, photocopy it at 98% of its original size. Or download a corrected copy of the pattern at woodmagazine.com/205correct.
205 July 2011 60 Construction-Grade Tractor/Trailers The patterns for the Construction-Grade Hauler in issue 205 (July 2011) were printed 2% too large in the WOOD Patternsıı insert. To correctly size the patterns, photocopy them at 98% of their original size. Or you can download a PDF file at woodmagazine.com/205correct with correctly sized patterns that you can then print out. Because there are so many variables with individual computers that can affect the size of the printout, we recommend measuring the patterns after you print them to verify they match the indicated dimensions before you begin work.
206 September 2011 12 Safely saw paper-thin veneer Drawing label Hanger bolt should be Zero-clearance insert.
206 September 2011 73 Floating-Top Table Drawing 1 Leg, Drawing 3 Exploded View, and 1a Tenon and Mortise Detail: Mortise on Leg A should be 13/16 inch deep not 15/16 inch deep
207 October 2011 40 Fold-Flat 3-in-1 Workbench Drawing 2: To allow room for the leg levelers, the legs (M) should be 31-3/4 inches long, not 32-3/4 inches.
207 October 2011 41 Fold-Flat 3-in-1 Workbench Drawing 3: Correct dimensions for the taper is 10-3/4 inchs (not 11 inches) and 21 inches (not 21-3/4 inches). Legs (M) length should be 31-3/4 inches, not 32-3/4 inches. See Sounding Board issue 209 page 8.
207 October 2011 42 Fold-Flat 3-in-1 Workbench Materials List: Legs (M) should be 31-3/4 inches, not 32-3/4 inches.
207 October 2011 65 8 ways to make end-to-end joints that hold Update photo caption for upper left-hand corner photo: This spline measures a third the tickness of the pieces to be joined, with the grain running parallel to the spline length.
208 November 2011 36 Media Center Materials List rails (Z) length should be 15-7/8 inches, not 15-1/8 inches.
208 November 2011 66 23-Gauge Pinners Bostitch HP118K fasteners length are 1/2 to 1-3/16
209 Dec/Jan 2011/2012 30 Miter-gauge extension For machining the 5/8" T-slots along the back and top edges of the body/extendable stop, we started by cutting a 3/8" dado 7/16" deep. Then, we used the Rockler T-Slot Cutter router bit (part no. 26099) to rout the slots in the edges of the dadoes. If you don't have such a bit, you could also create each T-slot by cutting a 5/8" dado 7/16" deep and glue two 1/4"-wide strips 1/8" thick in place to create the T-slot in each dado. Change Drawing Body/Extendable Stop T-slot measurements 1/8" to 3/16" and 1/2" to 5/8". See Sounding Board issue 213, page 6.
209 Dec/Jan 2011/2012 55 Box-joint jig Guide length is 11-1/2 inches not 11 inches as shown
210 March 2012 40, 42 Fold-Flat Sheet-Goods Mover An incorrect dimension was printed for the front legs (G) and rear legs (H). Drawing 3 and the Materials List parts G and H should have a length of 34-7/8 inches, not 39 inches.
212 July 2012 3 On our Web site Update: Digital issues of WOOD on iPad, Android tablet, and Nook Color for as little as $2.99 per month.
212 July 2012 28 Easy Swingin' Arbor Update: See Sounding Board issue 213, page 6.
212 July 2012 50 Woodworking Evolved - CNC Machines Wrong photo is shown for the Laguna CNC IQ, the photo is actualy of the Laguna CNC Pro IQ.

 


 

Newsstand specials
Newsstand Specials
ISSUE
#
ISSUE
MO / YR
PAGE
#
ARTICLE CORRECTION / ADDITION
1991 335 Great Shop Tips 2 Quick 'N' Easy Bandsaw Extension Table The blade kerf for the bandsaw extension table can be made as shown, by cutting a kerf in from the left-hand side of the plywood table slightly wider than the blade. Or, an easier way to do this would be to slide the wood table through the blade, leaving a kerf behind the blade in the clamped-down extension table.
1993 Sensational Gifts You Can Build 80 Quilt Rack Bill of Materials: Part K quantity 1
1994 Outdoor projects 30 Adirondack Rocker Note: Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 34.
97/99 Country Workshop 52 Grandma's Pie Safe Side Frames: 3 1/4" to top edge of taper and bottom edge of rail I
97/99 Country Workshop 53 Grandma's Pie Safe Buying Guide: telephone area code changed to 570; hardware change to polished brass latch
1998 Outdoor Projects You Can Build 19 Patio Glider Buying guide: New address McFeely's, PO Box 11169, Lynchburg, VA 24506-9963 or call 800/443-7937
1998 Holiday Decorations & Gifts 29 Snowman Buying Guide address change: Roberts Studio, 2620 Heather Road, Seymour, TN 37865, 800/316-9010
1998 Outdoor Projects You Can Build 59, 65 Adirondack Rocker Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 64 and 65.
1999 Furniture You Can Build 8 Rolltop Writing Desk Note: Tambour kit in buying guide is no longer available
1999 Furniture You Can Build 10 Rolltop Writing Desk Add to Supplies: 1" brass knob (6) and 1 1/4" brass knob (2)
1999 Furniture You Can Build 15 Rolltop Writing Desk Buying Guide: Tambour and knobs no longer available
1999 Furniture You Can Build 15 Rolltop Writing Desk Taper Jig: new phone Constantines Wood Center 954/561-1716, www.constantines.com
1999 Furniture You Can Build 48 Capacious Country Cabinet Supplies: Stanley hinges are no longer available. See plan DP-00060 for updated project.
1999 Furniture You Can Build 54 Glass-Topped Table Buying guide is no longer available.
1999 Furniture You Can Build 64 Mission Dining Set Buying Guide: kit discontinued. Tabletop fasteners #34215, T-nuts #26054, and floor guides #18657 available from Rockler at 800/279-4441 or rockler.com; wooden table slides #51040 available from Classic Designs by Matthew Burak at 800/748-3480 or tablelegs.com; table aligners #JH 3 available from Woodworker's Hardware at 800/383-0130 or wwhardware.com
1999 Furniture You Can Build 69 Mission Chair (Dining Chair) Side Frame Assembly: Part D is 15 5/16" length
1999 Outdoor Projects You Can Build 18 Picnic Suite Cutting Core Block, Part C: change 3 1/4" width to 3"; 13/16" to 3/4", 1 5/8" to 1 1/2", 2 7/16" to 2 1/4"
1999 Outdoor Projects You Can Build 18 Picnic Suite Cutting Core Block, Tablesaw Fence: change 1 3/8" to 1 5/16", 2 3/4" to 2 5/8"
1999 Outdoor Projects You Can Build 19 Picnic Suite Table Exploded View: Part C, Core Block, 2 3/4" change to 2 5/8"
1999 Outdoor Projects You Can Build 19 Picnic Suite Materials List changes: 1 5/8" Thickness to 1 1/2"; Part C Thickness 2 5/8"; Part C Width to 3"; part C Laminated Redwood
1999 Outdoor Projects You Can Build 20 Picnic Suite Step 11: text change to cut the block to 2 5/8"x3"; set the fence 2 1/4" away from the base of the blade; then make the cut
2001 30+ Great Gifts 29 Timeless Timekeeper Buying Guide: Supplier for quartersawn oak no longer available.
2001 30+ Great Gifts 32 Wake-Up Call Buying Guide is no longer available, no other source
2001 30+ Great Gifts 56 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2001 30+ Great Gifts 76 Snowman Buying Guide, new address: Roberts Studio, 2620 Heather Road, Seymour, TN 37865, 800/316-9010
2001 Best-Ever Workshops 27 Universal wall cabinet system Exploded View: Change 3/4x2 inch non-mortise hinge to 7/8x2-1/2 inch non-mortise hinge
2001 Best-Ever Workshops 29 Universal wall cabinet system Buying Guide, hardware: Change brass pull to cat. no. 39768; change no-mortise hinge to 7/8x2-1/2 inch
2001 Best-Ever Workshops 66 Full-service workbench Buying Guide Vise: New address 1177 Rosemar Road, P.O. Box 1686, Parkersburg, WV 26102
2001 Best-Ever Workshops 79 Swivel-topped tool cabinet Step 8: use locking swivel and fixed casters
2001 Best-Ever Workshops 80 Swivel-topped tool cabinet Supplies: use 2–2 1/2" locking swivel casters
2001 Best-Ever Workshops 81 Swivel-topped tool cabinet Exploded View: 2 1/2" locking swivel caster
2001 Best-Ever Workshops 95 Wiring Your Shop A subpanel requires two separate bus bars, one for the ground wires and one for the neutral wires. The ground bus bar amounts directly to the panel box, and the neutral bus bar should rest on an insulating block to keep the neutral wires from contacting the panel box. Also, in a subpanel, the ground wire must come from the main service entrance panel to provide a "least resistance" ground path for any fault current. Remember, don't take chances with electricity. Always consult local codes and get the advice of a certified electrician before beginning any do-it-yourself electrical work.
2001 Great Outdoor Projects 12 Drive Screws that Hold Labels switched on photo: Phillips/square drive and Star (Torx) drive
2002 Storage Solutions 66-67 Bedroom Solutions (loft bed) Bill of Materials/illustration: Eliminate part E, make 2 part D corner posts
2002 101 Workshop Projects 18 Workbench Tool Crib End Detail: 3/8" hole should be 1 3/4" from edge
2002 101 Workshop Projects 25 Binder Drilling Jig Part D: 1/4" dia. Dowel pins not 3/8"
2002 101 Workshop Projects 27 Drafting/Reference Center Self-closing hinge should be 12" not 14". Available from: Wooworker's Hardware (#KV8080 PEZ12) 800/383-0130
Arrow for 1/4x3/4x15 1/2 maple goes to front edge of board for a band. New Buying Guide for 4-position multiuse bracket (3/03) is now Woodworker's Hardware (800/383-0130) #KV0206 ZC 12
2002 101 Workshop Projects 47 Depth Gauge Step 2: 7/64" holes through the brass (not 7/16")
2002 101 Workshop Projects 53 Masterful Marking Gauge Buying Guide parts are no longer available.
2002 101 Workshop Projects 62 Strip Sander Step 4: 7/64" pilot hole (not 7/16")
2002 101 Workshop Projects 80 Roll-Around Plywood Cart Side View, End Panel A: top, 3" should be 2 1/4"; angled side edge, first 18 3/4" should be 18 1/4"
2002 101 Workshop Projects 91 High & Mighty Tablesaw Jig Buying Guide should be: Schlabaugh & Sons Woodworking, 720 14th Street, Kalona, IA 52247, or call 800/346-9663
2002 101 Workshop Projects 97 Sliding-base taper jig Buying Guide Hardware Kit is no longer available.
2002 101 Workshop Projects 108 Pocket-Hole Routing Jig 15° stock should be 3/4x2 5/8x9 5/8"
2002 Best-Ever Workshops 27 Universal wall cabinet system Exploded View: Change 3/4x2 inch non-mortise hinge to 7/8x2-1/2 inch non-mortise hinge
2002 Best-Ever Workshops 29 Universal wall cabinet system Buying Guide, hardware: Change brass pull to cat. no. 39768; change no-mortise hinge to 7/8x2-1/2 inch
2002 Best-Ever Workshops 30 Forstner Bit Holders The photo is upside down
2002 Best-Ever Workshops 66 Full-service workbench Buying Guide Vise: New address 1177 Rosemar Road, P.O. Box 1686, Parkersburg, WV 26102
2002 Best-Ever Workshops 79 Swivel-topped tool cabinet Step 8: use locking swivel and fixed casters
2002 Best-Ever Workshops 80 Swivel-topped tool cabinet Supplies: use 2–2 1/2" locking swivel casters
2002 Best-Ever Workshops 81 Swivel-topped tool cabinet Exploded View: 2 1/2" locking swivel caster
2002 Great Outdoor Projects 39 Classic Adirondack Step 3: Clamp a fence to your drill-press table 1 7/16" not 17/16" from the center of the bit.
2002 Great Outdoor Projects 17 Patio Glider Buying guide: New address McFeely's, PO Box 11169, Lynchburg, VA 24506-9963 or call 800/443-7937
2003 Best-Ever Outdoor Projects 6 Adirondack Chair Step 3: Clamp a fence to your drill-press table 1 7/16" not 17/16" from the center of the bit.
2003 Best-Ever Outdoor Projects 25 Adirondack Rocker Note: Full-size patterns are no longer available for the rocker. Enlarge the patterns on page 24 and 25.
2003

Best-Ever Outdoor Projects

28 Picnic Suite Table Exploded View: Part C, Core Block, 2 3/4" change to 2 5/8"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Cutting Core Block, Part C: change 3 1/4" width to 3"; 13/16" to 3/4", 1 5/8" to 1 1/2", 2 7/16" to 2 1/4"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Cutting the Core Block, Tablesaw Fence: change 1 3/8" to 1 5/16", 2 3/4" to 2 5/8"
2003 Best-Ever Outdoor Projects 29 Picnic Suite Step 11: text change to cut the block to 2 5/8"x3"; set the fence 2 1/4" away from the base of the blade; then make the cut
2003 Best-Ever Outdoor Projects 31 Picnic Suite Materials List changes: 1 5/8" Thickness to 1 1/2"; Part C Thickness 2 5/8"; Part C Width to 3"; part C Laminated Redwood
2003 Best-Ever Outdoor Projects 91 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2003 Best-Ever Outdoor Projects 105 Sees & Such Snack Shop Change "However, birds that typcically feed on the ground, like cardinals and juncoes, use a crevice in a tree bark to hold their seed while they peck it open." to "However, cardinals and juncos use the platform board. Nuthatches wedge seed into a crevice to peck."
2003 Best-Ever Workshop Solutions 14 One workhorse of a workbench Buying Guide, Vise: Quick-release vise, no. 144844. Woodcraft, 800-225-1153, woodcraft.com. Bench dogs no longer available from Woodcraft. Use bench dogs of your choice.
2003 Best-Ever Workshop Solutions 21 Labor-of-Love Workbench Materials key: B-birch, BP-birch plywood
2003 Best-Ever Workshop Solutions 21 Labor-of-Love Workbench Buying Guide, Hardware: wood pulls are 3-7/8" not 4". Laminated maple benchtop, part no. BBT30060, Dunn & Company, 800-728-3866.
2003 Best-Ever Workshop Solutions 32, 35 Mobile mitersaw center Exploded View and Buying Guide: fixed casters no. 141053; swivel casters no. 141050; 3" wire pull no. 836159.
2003 Best-Ever Workshop Solutions 51 Tilt-top router table Drawing 8 Fence:Top view is Part Y not X. Front View is Part X not Y.
2003 Best-Ever Workshop Solutions 53 Tilt-top router table Materials List: Base is Part Y; Fence is Part X.
2003 Best-Ever Workshop Solutions 54 Full-service benchtop router table Use T-track instead of T-slotted mini tracks and mini track
2003 Best-Ever Workshop Solutions 55 Full-service benchtop router table Drawing 1: change mini-track to T-track; screws for T-track are #6x1/2 inch F.H. wood screws; change Round-knob to 3/4 inch stud not 1/2 inch stud
2003 Best-Ever Workshop Solutions 56 Full-service benchtop router table Step 5: change mini-track to T-track
2003 Best-Ever Workshop Solutions 57 Full-service benchtop router table Drawing 3: change mini-track to T-track; step 3 change mini-track to T-track
2003 Best-Ever Workshop Solutions 59 Full-service benchtop router table Step 2: change mini-track to T-track; Step 4 "See Buying Guide for our source of knobs."
2003 Best-Ever Workshop Solutions 59 Full-service benchtop router table Supplies: move 1/4 inch hexhead bolts from Buying Guide to Supplies list; add #6x1/2 inch F.H. wood screws. Updated Buying Guide: Hardware. Knobs with 1/4 inch threaded insert no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36 inch T-track no. 12K79.24 (1); 24 inch T-track no. 12K79.22 (2); 2-1/2 inch vac port no. 03J61.10 (1). Lee Valley, 800-871-8158, leevalley.com. Switch: Safety power switch no. 20915. Rockler, 800-279-4441, rockler.com
2003 Best-Ever Workshop Solutions 66 Router retrofit Buying Guide, router plate. Insert plate, 3/8x12x12" acrylic no. 16L71. Woodcraft, 800-225-1153, woodcraft.com
2003 Best-Ever Workshop Solutions 88 Tablesaw accessories cabinet Buying Guide, hardware. 3" wire pulls no. 836159.
2003 Best-Ever Workshop Solutions 110 Drill-press table Buying Guide. Ready-to-assemble kit no longer available.
2003 Best-Ever Furniture You Can Build 69 The Entertainer Supplies: Stanley hinges are no longer available. See plan DP-00060 for updated project.
2003 Best-Ever Furniture You Can Build 84 Shelving Showcase Section View: 1/4" flutes 3/16" deep
2003 Best-Ever Furniture You Can Build 87 Shelving Showcase Drawing 8b should be 8a
2004 Best-Ever Outdoor Projects 111 Grand entrance (gate) Drawing 6 and Step 4, Part R: Lay part R diagonally across the assembly with the top end opposite the hinge side.
2004 Best-Ever Outdoor Projects 113 Grand entrance (gate) Buying Guide: HardieSingle Individual Shingles, web site www.jameshardie.com
2004 Best-Ever Workshop Tips, Jigs and Organizers 22 Bandsaw Fence 3/8" all-thread rod 1" longer than A not 26 3/8" long
2004 Best-Ever Workshop Tips, Jigs and Organizers 41 Dovetail-Jig Stabilizer Fixture Porter-Cable model 5008 Dovetail Templet is no longer available.
2004 Best-Ever Workshop Tips, Jigs and Organizers 97 Rout parallel slots to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2004 101 Workshop Projects 53 Masterful Marking Gauge Buying Guide parts are no longer available.
2004 101 Workshop Projects 97 Sliding-base taper jig Buying Guide Hardware Kit is no longer available.
2005 450+ Best-Ever Shop Tips 21 One-handed bar clamp keeps crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2005 Best-Ever Outdoor Projects 12 Drive Screws that Hold Labels switched on photo: Phillips/square drive and Star (Torx) drive
2005 Best-Ever Outdoor Projects 128 Music in the wind Buying Guide, tuned chime rods, are no longer available.
2005 Best-Ever Workshops 77 Tough-Stuff Workbench Update Sources, Cabinets: Can also use 28" full-extension drawer slides no. 02K30.28
2005 Best-Ever Workshop Solutions 14 One workhorse of a workbench Buying Guide: Bench dogs no longer available from Woodcraft. Use bench dogs of your choice.
2005 Best-Ever Workshop Solutions 21 Labor of love workbench Buying Guide, Hardware: wood pulls are 3-7/8" not 4". Laminated maple benchtop, part no. BBT30060, Dunn & Company, 800-728-3866.
2005 Best-Ever Workshop Solutions 32, 35 Mobile mitersaw center Buying Guide, Hardware: 3" wire pull no. 836159.
2005 Best-Ever Workshop Solutions 51 Tilt-top router table Drawing 8 Fence: Top view is Part Y not X. Front view is Part X not Y.
2005 Best-Ever Workshop Solutions 53 Tilt-top router table Materials List: Base is Part Y; Fence is Part X.
2005 Best-Ever Workshop Solutions 54 Full-service benchtop router table Use T-track instead of T-slotted mini tracks and mini track
2005 Best-Ever Workshop Solutions 55 Full-service benchtop router table Drawing 1: change mini-track to T-track; screws for T-track are #6x1/2 inch F.H. wood screws; change Round-knob to 3/4 inch stud not 1/2 inch stud
2005 Best-Ever Workshop Solutions 56 Full-service benchtop router table Step 5: change mini-track to T-track
2005 Best-Ever Workshop Solutions 57 Full-service benchtop router table Drawing 3: change mini-track to T-track; step 3 change mini-track to T-track
2005 Best-Ever Workshop Solutions 59 Full-service benchtop router table Step 2: change mini-track to T-track; Step 4 "See Buying Guide for our source of knobs."
2005 Best-Ever Workshop Solutions 59 Full-service benchtop router table Supplies: move 1/4 inch hexhead bolts from Buying Guide to Supplies list; add #6x1/2 inch F.H. wood screws. Updated Buying Guide: Hardware. Knobs with 1/4 inch threaded insert no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36 inch T-track no. 12K79.24 (1); 24 inch T-track no. 12K79.22 (2); 2-1/2 inch vac port no. 03J61.10 (1). Lee Valley, 800-871-8158, leevalley.com. Switch: Safety power switch no. 20915. Rockler, 800-279-4441, rockler.com
2005 Best-Ever Workshop Solutions 65, 66 Router retrofit Buying Guide, Router plate. Insert plate, 3/8x12x12" acrylic no. 16L71. Woodcraft, 800-225-1153, woodcraft.com
2005 Best-Ever Workshop Solutions 88 Tablesaw accessories cabinet Buying Guide, Hardware. 3 inch wire pulls (2) no. 836159. Woodcraft.
2005 Best-Ever Workshop Solutions 110 Drill-press table Buying Guide, Ready-to-assemble kit is no longer available.
2005 450+ Best-Ever Shop Tips 13 Super-Simple Taper Jig Buying Guide Hardware Kit is no longer available.
2006 Great Outdoor Projects 66 Down-to-earth bench Buying Guide: Foam Kneeling Pads. Part no. changed to KP816. Sold in single pack.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
9 Weather station Source, instruments: Kit is no longer available.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
33 Occasional table Scrapwood router trammel: Reverse arrow on routing direction towards top of the circle
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
47 Treasured chest Drawing 1b is missing: Part M notch is 3/8 by 3/8 inches
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
56 Kid's room ensemble Cork source is no longer available. Cork: Art and craft supply stores. Adhesive: 3M Super77 Multi-Purpose Adhesive, hardware stores and home centers.
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
73 Pendulum Cradle Drawing 2: Measurement 9-5/8" should be 10-1/8"; 3-1/8" should be 2-1/4"; 13" should be 13-3/8"
2006 America's
Best-Ever Woodworking Projects
& Shop Tips
77 Pendulum Cradle Sources, Cradle Pad: 17x31" vinyl-covered foam pad, No. A002112. Call Ababy.com at 877-552-2229 or go to ababy.com
2006 Best-Ever Home Shop Ideas 10 Bright ideas Lights Now product is no longer available.
2006 Best-Ever Home Shop Ideas 26-27 Guide to base and wall units for our garage California Closets phone 800/274-6754;
osullivan-furniture-online.com phone 866/914-4204;
Garage Tek phone 866/664-2724; Garage Storage Cabinets website garagestoragecabinets.com;
Lista website listacabinets.com; Mitchell Cabinets by IST now Cooper Cabinet Systems, available in variety of sizes, coopercabinetsystems.com
2006 Best-Ever Home Shop Ideas 10 Bright ideas Lights Now product is no longer available.
2006 Best-Ever Home Shop Ideas 59 Super-flexible shop storage Hardware update: plastic sliding door track, no. 10007, shelf pins, no. 22773, available from Rockler, rockler.com. 800-279-4441
2006 Best-Ever Home Shop Ideas 72 Mobile sanding center Buying Guides of vacuum and dust-collection system are no longer available
2006 Best-Ever Home Shop Ideas 77 Tough-stuff workbench Sources, cabinet: full-extension drawer slides part no. 02K30.28
2006 Best-Ever Home Shop Ideas 77 Tough-stuff workbench Plans for workshop Stool are no longer available.
2006 Best-Ever Home Shop Ideas 90 3-in-1 Work Support Source, hardware, update: aluminum mini-track available from Rockler, rockler.com, 800-279-4441, part no. 34676
2006 Best-Ever Home Shop Ideas 101 Super-flexible shop storage Hardware update: plastic sliding door track, no. 10007, shelf pins, no. 22773, available from Rockler, rockler.com. 800-279-4441
2006 Best-Ever Home Shop Ideas 115 Whole-shop air-cleaning system Buying guide, blower/motor: Grainger changed the motor to stock no. 7D554, 1,280-1,587 cfm, new phone no. 888-361-8649 Note: The blower cabinet and filter cabinet are based on the particular model we used. Measure your blower and filter before beginning construction to make sure they will fit in the cabinets dimensioned here. Cabinet sizes may need to be adjusted for other models of blowers and filters.
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 11 Dead-on 90 degree crosscut sled Drawing 1: guide bar change to 3/8x1/2x1-1/4 inch; Stopblock change to 3/8 inch dado 1/4 inch deep 7/8 inch from top edge; washer is 1/4 inch flat washer
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 78 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 79 Mitersaw work station Drawing 2, BASE and Materials List: J is 14-3/4 inches not 14 inches; Key 3-1/2 inches is 3-1/4 inches.
2006 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 81 Wall Cabinet Drawing 4: Shelf holes start 7" inches from top not 7-1/4 inches from top of part A.
2007 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 81 Enlarge a hole of almost any shape Illustration, Step 2: Arrow showing bit direction should be pointing to the left
2007 215 Fixes for Common Woodworking Mistakes 12 Fix 22 Photo labels should be: Loose hook: 12-13/16; Tight hook: 12-3/4 and move pencil mark to 12-3/4
2007 215 Fixes for Common Woodworking Mistakes 26 Fix 42 Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2007 215 Fixes for Common Woodworking Mistakes 56 Fix 92 How Climb-Cutting Give Smoother Results: Shape of bit should be round not oval
2007 215 Fixes for Common Woodworking Mistakes 68 Fix 103 Drawing 1, Box-Joint Sled: The width of the blade guard and acrylic on the box-joint sled is 3-1/4" wide to allow for the rotating of the four-arm knobs. The adjusted slot length is 3/4" and location is 3-3/8" from outside edge of fence.
2007 Best-Ever Decks & Backyard Projects 103 Grand entrance (gate) Drawing 6 and Step 4, Part R: Lay part R diagonally across the assembly with the top end opposite the hinge side.
2007 Best-Ever Decks & Backyard Projects 105 Grand entrance (gate) Buying Guide: HardieSingle Individual Shingles, web site www.jameshardie.com
2007 America's Best Home Workshops 144-145 Guide to base and wall units for our garage California Closets phone 800/274-6754;
osullivan-furniture-online.com phone 866/914-4204;
Garage Storage Cabinets website garagestoragecabinets.com;
Lista phone 888/897-9050, website listacabinets.com;
Mitchell Cabinets by IST now Cooper Cabinet Systems, available in variety of sizes
2007 Best-Ever Workshop Jigs, Tips, and Ideas 42 Rour parallel slots to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2007 Best-Ever Workshop Jigs, Tips, and Ideas 76 Wider is Better for Resaw Feather Boards The feather-board fingers apply pressure to workpiece only in front of the blade.
2007 Best-Ever Workshop Jigs, Tips, and Ideas 125 Steady-as-She-Goes Biscuit Joiner Jig Handhold: 1 inchradius not 2 inch radius; 3/4 inch radius not 1-1/2 inch radius
2007 450+ Best-Ever Shop Tips 13 Super-Simple Taper Jig Buying Guide Hardware Kit is no longer available.
2007 450+ Best-Ever Shop Tips 21 One-handed bar clamp keeps crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2007 450+ Best-Ever Shop Tips 22 Clean-cut lids for closed boxes Missing copy at end of tip: the glue before sanding to remove the saw marks. -John Ash, Lockport, Ill.
2008 Best-Ever Router Tips, Tricks & Jigs 82 Full-service bench-top router table Source, hardware: Knobs no. 27R14 (8); round knobs no. 27R11 (4); acrylic insert plate no. 16L71 (1). Woodcraft, 800-225-1153, woodcraft.com. 36" T-track no. 12K79.24; 24" T-track no. 12K79.22; 2-1/2" vac port no. 03J61.10. Lee Valley, 800-871-8158, leevalley.com. Safety power tool switch no. 20915. Rockler, 800-279-4441.
2008 Best-Ever Router Tips, Tricks & Jigs 113 Rout parallel sltos to perfection Illustration: Switch labels Dovetail slots with Slots precut with 5/16" straight bit
2008 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 11 Dead-on 90 degree crosscut sled Drawing 1: guide bar change to 3/8x1/2x1-1/4 inch; Stopblock change to 3/8 inch dado 1/4 inch deep 7/8 inch from top edge; washer is 1/4 inch flat washer
2008 Best-Ever Woodworking Jigs, Homemade Tools & Shop Organizers 78 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2008 America's Best Home Workshops 112 Drill-Press/Mortiser Stand Delta 50-322 Planer Stand from toolmarts.com
2009 Best-Ever Home Shop Ideas 25 Workshop Cabinetry Gladiator Web address is: gladiatorw.com
2009 Best-Ever Home Shop Ideas 28 Get Wired A subpanel requires two separate bus bars, one for the ground wires and one for the neutral wires. The ground bus bar amounts directly to the panel box, and the neutral bus bar should rest on an insulating block to keep the neutral wires from contacting the panel box. Also, in a subpanel, the ground wire must come from the main service entrance panel to provide a "least resistance" ground path for any fault current. Remember, don't take chances with electricity. Always consult local codes and get the advice of a certified electrician before beginning any do-it-yourself electrical work.
2009 Best-Ever Home Shop Ideas 46 Versa-Cab Drawing 1, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2009 Best-Ever Home Shop Ideas 61 Bench-tool System Project Highlights, item 4: Locking casters not dual-locking casters
2009 Best-Ever Home Shop Ideas 63 Bench-tool System Drawing 4: Locking swivel casters not dual-locking swivel caster
2009 Best-Ever Home Shop Ideas 64 Bench-tool System Drawing 5: 4" locking swivel caster not dual-locking swivel caster; Source: Casters, 4" locking swivel plate casters no 00K21.41. Lee Valley Tools, leevalley.com, 800-871-8158.
2009 Best-Ever Home Shop Ideas 77 Tablesaw Workbench Source: Casters no. 00K21.41, Lee Valley Tools, leevalley.com, 800-871-8158
2009 Best-Ever Home Shop Ideas 78 Tablesaw Workbench Drawing 2: locking swivel caster not double-locking swivel caster
2009 Best-Ever Outdoor Projects 23 Cozy rocker Full-size patterns for Cozy Rocker are no longer available.
2009 Best-Ever Outdoor Projects 81 Full-size patterns for the projects in this magazine Full-size patterns for Adirondack Lawn Rocker Plan OFS-1016 are no longer available.
2009 101+ Best-Ever Workshop Projects 51 Versa-Cab Drawing, part C, 4-1/4" change to 4-1/8" from edge to dadoes
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 65 Tablesaw Workbench Source: Casters no. 00K21.41, Lee Valley Tools, leevalley.com, 800-871-8158s
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 66 Tablesaw Workbench Drawing 2: locking swivel caster not double-locking swivel caster
2009 Best-Ever Tablesaw Jigs, Tips & Ideas 124 Bar clamp helps keep crosscuts square Remove text: It also provides me with a convenient handle to help push the piece through the saw.
2010 Best-Ever Storage Solutions 21 The Shelf Maker's Complete Guide Adjustable support options: Low-profile shelf standard is shown in photo but not labeled, used with low-profile support labeled as before and after insertion.
2010 Best-Ever Storage Solutions 76 Closet Storage Supplies: See items in Source, page 80 not 94.
2010 Best-Ever Workshop Jigs, Tips, and Ideas 109 Steady-as-She-Goes Biscuit Joiner Jig Handhold: 1 inchradius not 2 inch radius; 3/4 inch radius not 1-1/2 inch radius
2011 America's Best Home Workshops 106 Drill-Press/Mortiser Stand Delta 50-322 Planer Stand from toolmarts.com
2011 Great Garage Makeovers 16 dream garage on the prairie There is a layer of drywall sandwiched between the MDF and 2x6 (not shown in Section View and Exploded View)
2011 Great Garage Makeovers 74-75 safe, solid, and secure Model number updates: Stanley Tool Works new model FMST20061; Craftsman new model 31017 and model 31016
2011 Great Garage Makeovers 93 Gallery of Garage Art Web site for "Check the Oil!" is checktheoilmagazine.com
2011 101 Best-Ever Workshop Projects 36 Mitered half-lap joinery jig twosome Build the mitered half-lap jig using the width of your frame as the length of fence reach beyond the base.
2011 101 Best-Ever Workshop Projects 98 Pocket-hole jig organizer and base Organizer was designed to fit a Kreg K3 jig. You may need to adapt the dimensions and workpiece support height to suit your jig.
2011 101 Best-Ever Project and Shop Tips 56-60 Shaker Clock Source: Clock kit: Radio-controlled clock movement no longer available. Replaced with quartz clock movement. Order kit no. SK-WAL-Q for walnut or kit no. SK-CH-Q for cherry.

 

shim

Wood Magazine