8 ways to make end-to-end joints that hold
SPECIAL OFFER: - Limited Time Only!
(The ad below will not display on your printed page)

Wood Magazine

8 ways to make end-to-end joints that hold

Finger joints
Enlarge Image
 
Finger joints provide face- or
edge-grain gluing surfaces to
end-to-end joints for a stronger
glue bond.

Any joint that butts end grain to end grain will be weak because you're gluing wood fibers at their porous ends instead of along their sides. (Picture trying to glue two drinking straws together at their ends instead of along their sides.) Fortunately, you can strengthen end-to-end joints for those rare occasions when they're necessary, such as connecting two pieces of crown molding on a long wall, or making the most of pieces that are too short for your project but too long to scrap.

Boiled down to basics, you must either add reinforcements, such as plates, dowels, or screws, or cut the joint in a way that creates mechanical strength and exposes more face or edge grain for a stronger bond, such as the finger joint, shown at right. Check out these eight solutions, from basic to beautiful.


 

Plain, practical straps
Screwing board with 5th screw
Enlarge Image
 
Eight #8x1/2" flathead wood screw
s plus glue hold this end-to-end
crown molding joint tightly together.

Plain, practical straps

Use simple metal or plywood straps to reinforce butt joints where they can be hidden or where appearance isn't important, such as on the back side of a wide crown molding where you can't afford any waste. Making your own custom-sized straps from 1/4" plywood saves you money and provides a strong gluing surface.

To install a wooden strap, cut it as wide as the workpiece allows. If you're joining pieces with a profile on the opposite face, such as molding, locate the screw holes over the thickest profile points -- at the peak of a ridge or curve, for example.

To make the joint, glue and screw one side of the strap to a workpiece. After the glue dries, glue the other half of the strap, and clamp the assembly to a flat surface. For a tight joint, raise the other workpiece about 1/4" at 3' from the end being jointed. Then press the pieces together as you add the mounting screws, as shown right. Lay both pieces flat and allow the glue to dry before handling the joint.


 

Pocket-hole screws
Board with screw holes in it
Enlarge Image
 
Pocket holes drilled into the back
face (top) are invisible from the front.
The screw then pulls the pieces
together (bottom).

Pocket-hole screws

Here's another easy method to fasten butt joints in a hurry. To install pocket-hole screws, drill an angled hole through one workpiece and into another. A screw inserted into the hole pulls the pieces together, as shown at right. Workpieces should be at least 1/2" thick (using 1" screws), and you can attach parts 1 1/2" or thicker using 2 5/8" screws. To learn more about making pocket-hole joinery, go to woodmagazine.com/pocketholes.


 

Splines provide inner strength
Spline between to boards
Enlarge Image
 
This spline measures a third the
thickness of the pieces to be joined,
with the grain running perpendicular
to the spline length.
Joint
Enlarge Image
 
Round over the spline corners for
a tight fit in the slot, but cut the
splines 1/32" narrower than the
combined depths of the slots.
Orange push pad against board
Enlarge Image
 
A push pad holds this test scrap
firmly against the router fence. Add
a high auxiliary fence to keep long
workpieces from tilting.
Chart
Enlarge Image
 

Splines provide inner strength

Splines create a face-to-face glue surface that resists flexing. Use through splines for an easy-to-make connection with visible splines. Mark each joint on its top face and set the saw blade 3/4" high? -- half the length of the splines. Orient the top faces of each piece against your rip fence for consistent groove positions between pieces. To keep extra-long pieces steady, add an auxiliary fence. Using a backer block to stop tear-out, cut kerfs on the ends to form a groove as wide as one-third the thickness of your stock.

Next, plane and saw the spline blank stock to match the width and combined depth of the grooves. You can make splines from plywood or solid stock. If you choose solid stock, as shown right, orient the spline grain with the workpiece grain. Insert the spline; then glue and clamp the pieces.

For not much more work, create a concealed spline, like the one shown in middle photo, that disappears after you assemble the joint. We made this joint using a 1/4" straight bit on a table-mounted router. Set the bit height to just more than half the width of your splines. Then adjust your router table fence to center the bit on the thickness of the workpiece ends.

Next, build a simple jig to guide your workpieces. From scrap slightly thicker than your workpieces, cut two stopblocks. Space them a distance apart that's twice the width of your workpiece minus mortise insets from both edges. Then attach a crosspiece that's 1/2" wider than the bit height for added safety and control. Clamp the connected stopblocks of the finished jig to the router table fence so they're equal distances from the bit, as shown bottom right.

To keep minor fence adjustment errors from creating an uneven joint, mark the top faces of your workpieces and have them facing you while routing the slots. Using a pushpad, press the workpiece against the router fence and down the edge of the right stop block to the router table. Slide the workpiece to the left stop block, as shown bottom right, and raise it clear of the bit.


 

Drill and dowel

Drill and dowel

A dowel joint, shown at right, provides another invisible connection. Butt the pieces to be joined and mark dowel positions on both faces. Position a doweling jig over the marks, and drill holes 1/16" deeper than half the dowel length. On one piece, spread glue within the holes, insert the dowels, and clamp it to a flat surface. On the other piece, glue the end grain and holes, force the pieces together, and clamp until dry.


 

Bevel-cut scarf joints
Saw blade at an angle
Enlarge Image
 
Cut crown-molding ends on
opposite sides of the blade
for a tight end-to-end joint.

Bevel-cut scarf joints

By cutting ends at an angle before joining them, you expose more long grain for a better bond. The sharper the angle, the larger and better the gluing surface. For example, a 45° bevel increases the gluing surface by about 40 percent and helps conceal the joint line on a profiled surface. To match the angles, cut one end on one side of the saw blade and the mating end on the opposite side, as shown at right. Even if your blade bevel angle varies slightly from 45°, the pieces will mate.

To join the halves, clamp the lower one against a flat surface. Then clamp the upper piece down and against the bevel on the lower piece. Align the pieces with a straightedge, if necessary.


 

Miter-cut scarf joints
Marking a triangle piece of board
Enlarge Image
 
To mark wider moldings, just
increase the size of this
4:1 angle guide.
Sanding side of board
Enlarge Image
 
Ride the edge of the router base along
the 4:1 angle guide for a smooth
glue edge.
Clamping board
Enlarge Image
 
A 4:1 angle increases this scarf
joint's gluing surface more
than 450 percent.

Miter-cut scarf joints

Try this joint for an even larger gluing surface. Begin by making a 4:1 angle guide that's more than double the width of the workpieces. (The guide shown in the photos measures 5x20" for a 2"-wide workpiece.) Identical cleats on both sides of the triangle help position it on the face of both workpieces, as shown at right. Mark angles on both workpieces, and bandsaw the pieces to within 1/32" of the lines on the waste sides.

Next, chuck a straight bit in your router. Clamp the guide and workpiece together against the top of a firm surface, such as your workbench, with the workpiece edge overhanging. Place the triangular piece of scrap removed by the bandsaw beneath the angled guide and next to the narrow tip, as shown in middle photo, to help stabilize the router base and back your cut at the tip. Then trim the remaining waste down to your marked line. Flip the guide upside down and rout the other workpiece.

To assemble the joint, glue the mitered edges and hold them loosely together so both edges form straight lines. Then clamp both pieces to a flat surface to prevent them from slipping when you clamp the joint together, as shown in bottom right photo.


 

Basic half-lap joints
Pencil marking with a square
Enlarge Image
 
Use the width of your workpieces
to mark the length of the overlap.
Cut board stack on one another
Enlarge Image
 
Fine-tune the dado blade height
using test cuts on scrap as thick
as the workpieces.
Marking Half-lap on board
Enlarge Image
 
Dado the start and end of the
half-lap on both workpieces together.
Then remove the material in between.
Boards marked with A & B
Enlarge Image
 
This half-lap joint creates a
durable face-grain connection between
the pieces. You can increase or
decrease the overlap as needed.

Basic half-lap joints

Attractive, strong, and easy to make on a tablesaw or router table, half-lap joints create face-to-face gluing surfaces. The more the overlap, the better the bond.

To make a simple half-lap joint, begin by marking your cuts. For identical laps, place both workpieces side by side with the ends flush and the appearance side up on one piece and down on the other. Mark an "X" where you'll cut your lap on each piece; then mark a line across both pieces and extend the lines from the faces to the edges on both pieces, as shown at right.

Next, install a dado set at least 5/8" wide in your tablesaw and set the blade height to cut half the thickness of your workpieces. Test the fit of the joint using scrap, as shown in second photo. Faces of the test scraps should be flush, with solid wood-to-wood contact at the laps.

Now, cut a dado from the marked joint lines to the ends, as shown in third photo. A miter-gauge extension helps position each pass and reduces tear-out. (One piece will be dadoed with the appearance side down.) Then test-fit the joint, as shown in bottom photo, and check for gaps between the laps or between the bench or saw top and one of the faces. Glue and clamp the laps for a permanent connection.


 

Tabled lap joints
Rabbet part together
Enlarge Image
 
For perfectly matching half-laps,
rabbet both workpieces side-by
side at the same time.
Test scrap
Enlarge Image
 
A rabbeted corner of one test
piece should just touch the dado
bottom in the other.
Rabbeted section
Enlarge Image
 
Cut both pieces edge to edge
at the same time for matching
dado widths.
2 boards together with gaps between them
Enlarge Image
 
Pieces of a tabled lap joint
lock together to form both a
mechanical connection and
a strong glue bond.

Tabled lap joints

This joint combines the strength of interconnecting parts with the large glue surface of a half-lap joint. To make it, add 1/4" to the workpiece width. (You'll remove it later as you fine-tune the joint.) Then measure that distance from the end of the workpiece. Mark both pieces at the same time as described for a basic half-lap joint. Duplicate these markings on a pair of test pieces the thickness of your final workpieces.

Use the same dado setup as for the basic half-lap, but instead set the blade height to exactly one-third the thickness of your workpieces. Then rabbet both parts and the two test pieces from your edge markings to the ends, as shown at right.

Now reset your dado blade height to exactly two-thirds the thickness of the workpieces. Using your scrap pieces, test and adjust the dado depth until the thicker portion toward the end rests within the thinner section so the faces of both pieces are flush, as shown in second photo.

Measure from the shoulder of the dado to a distance that equals one-half the width of the workpiece, and place a mark there. With both pieces clamped against the miter gauge, make two passes to define the width of this second pair of dadoes, as shown in third photo. Then cut the remaining dadoes.

To ensure a tight joint, gradually trim the ends of each piece separately until both fit the deeper dadoes, as shown in bottom photo. Then glue and clamp the pieces for a joint that shows you can stretch a board with style.

Find more shop-tested woodworking skills at: woodmagazine.com/shopskills


 

shim

Wood Magazine