7 safety rules to never violate
SPECIAL OFFER: - Limited Time Only!
(The ad below will not display on your printed page)

Free Year + Free Gift! Order NOW and get 1 FREE YEAR of Wood® Magazine! PLUS you'll get our Great Projects for Your Shop guide instantly! That's 2 full years (14 issues) for the 1-year-rate – just $28.00. This is a limited-time offer, so HURRY!
(U.S. orders only) (Click here for Canadian orders)

Email:

First Name:

Last Name:

Address:

City:

State:

Zip:

100% Money-Back Guarantee: You must be pleased, or you may cancel any time during the life of your subscription and receive a refund on any unserved issues – no questions asked. Wood® Magazine is currently published 7 times annually – subject to change without notice. Double issues may be published, which count as 2 issues. Applicable sales tax will be added. E-mail address required to access your account and member benefits online. We will not share your e-mail address with anyone. Click here to view our privacy policy.
Wood Magazine

7 safety rules to never violate

Listen to that little fella on your shoulder

Listen to that little fella on your shoulder

When you hear that voice in the back of your head saying, "this isn't right," listen to it and rethink the operation. Rehearse an unfamiliar cut first, without any spinning steel. If you feel uncomfortable with it, jig-up to make it safer, or find another way.


 

Inspect your tools
Red saw blade
Enlarge Image
 
Check blades for broken or
loose teeth like the one marked
here. Such damage can create a
dangerous imbalance in the blade.

Inspect your tools

Check every tool before use, even if you were the last to use it: Look for debris near the cutterhead or blade and any loose or misaligned parts that could become projectiles when you turn the tool on. Keep blades sharp and clean: Forcing a workpiece through a dull and dirty blade increases the risk of a hand slipping (and may cause burns and tearout on your workpiece, too).


 

Watch where you stand
Pushing board thru saw
Enlarge Image
 
Whether the fence is on the
left or right of the blade, stand
to the side of the blade opposite
the fence--body out of line with the cut.

Watch where you stand

Never put your body directly in line with the blade when making rip cuts at the tablesaw: If the board kicks back, it's coming straight at you. Also, never place your pushing hand in direct line with the cutting motion, regardless of the tool.


 

Tug the plug
On off switch
Enlarge Image
 
Unless you can see the loose
plug free of the outlet or the yellow
safety tab absent from the switch,
assume the tool's ready to go.

Tug the plug

When not in use or during blade changes, unplug power tools or, if the tool has one, remove the safety tab from the on/off switch. This prevents both you and shop visitors (young and old) from accidentally turning on a tool. The same principle applies to pneumatic tools: When adding fasteners to a nailer, always disconnect the air hose first.


 

Stay mentally sharp
Thing about food
Enlarge Image
 
Move finished pieces off your
machine, and take a break if
you get tired, bored with
repetitive cuts, or hungry.

Stay mentally sharp

Get comfortable, but not too comfortable, with your tools. When a project requires repeated cuts for identical parts -- making the same cut 20 times -- your mind can wander. Stay focused. Never walk away from a tool when it's running and always wait for the blade to come to a complete stop before reaching for cut-offs near the blade.


 

Get pushy
Using a push stick on table saw
Enlarge Image
 
This pushstick can pass right
over the blade and still support
the cutoff. Replace the heel when
it becomes too kerfed.

Get pushy

Use pushsticks designed with plenty of surface area in contact with the workpiece; they hold the board down while keeping your hand several inches from the blade. A pushstick doesn't have to be pretty, complicated, or expensive -- the shop-made one shown consists of just scrap 2x4 with an MDF heel. Keep a pushstick at each tool station and always within easy reach.


 

Keep it clean
Wooden bin
Enlarge Image
 
Don't just chuck your scrap in
a pile in the corner. Keep your
floors cleaner and pieces
separated with this cutoff bin.

Keep it clean

If your shop has a layer of sawdust as thick as urethane on a gym floor, that dust presents a slipping hazard. Sweep it up. Also, dispose or store loose cutoffs and tools not in use. Clear off machines before use and make sure there's nothing that may shift into your cutting path or the blade during the machine's operation.


 

shim

Wood Magazine