Return of the Mortise Machine
SPECIAL OFFER: - Limited Time Only!
(The ad below will not display on your printed page)

Free Year + Free Gift! Order NOW and get 1 FREE YEAR of Wood® Magazine! PLUS you'll get our Great Projects for Your Shop guide instantly! That's 2 full years (14 issues) for the 1-year-rate – just $28.00. This is a limited-time offer, so HURRY!
(U.S. orders only) (Click here for Canadian orders)

Email:

First Name:

Last Name:

Address:

City:

State:

Zip:

100% Money-Back Guarantee: You must be pleased, or you may cancel any time during the life of your subscription and receive a refund on any unserved issues – no questions asked. Wood® Magazine is currently published 7 times annually – subject to change without notice. Double issues may be published, which count as 2 issues. Applicable sales tax will be added. E-mail address required to access your account and member benefits online. We will not share your e-mail address with anyone. Click here to view our privacy policy.
Wood Magazine

Return of the Mortise Machine

Readers offer solutions to the machine's mysteries

We first showed you the Miller mortise-joint machine in the December 1997 issue. Back then, we left you with a question: How does it work? A number of you took up the challenge to explain this thing.


What do those rods do? Are they in backward?

Most speculation about how the Miller machine works centered on those mysterious, toothed rods. Some correspondents wondered if the machine in the photograph had been dismantled, and then reassembled incorrectly. "Reverse the rods!" they implored. This way, the rods' teeth would face outward and could grip against the adjustable blocks, helping to advance the cutter into the work.

That this machine could have been improperly assembled by some previous owner seemed entirely plausible. But then we heard from Loring McKenzie of Logansport, Indiana.

A tool collector, Loring sent photos of several mortise machines he owns, including a Miller. Close inspection of the photo of his Miller machine showed the rod teeth facing inward. We took this as evidence (though it's hardly conclusive) that the rods were installed correctly on Dick Gowen's machine that we showed.


testing
Enlarge Image
 
With the rods extending into pilot holes as in the section view (photo A), the Miller mortise machine works fairly well. (We predrilled the mortise. The machine would have cut cleaner sides had we not.) We had less success when we attempted to define the ends of the mortise with 3/4" holes. The machine would only cut this deep (photo B).

Is drilling the key?

Loring figures that the Miller machine was intended to finish a mortise first roughed out by drilling. Several other readers focused on that idea of drilling first, too. Some held that the entire mortise would be drilled out, and then cleaned up with the machine. Others leaned toward drilling two pilot holes, one at each end of the mortise. The more we thought about it, the more we came to accept the pilot-hole theory of operation. It was best expressed by Tom Oertling, a Galveston, Texas, woodworker trained in archaeology.

"I believe that the ends of the mortise were defined by two holes drilled straight down to the depth (and maybe plus a little) of the mortise," he wrote. The rods would then extend into the pilot holes, and the adjustable blocks would be adjusted to press them against the sides of the holes.

"Note that the ratchets are cut so that the rod will move down in the hole, but will bite (into the end-grain wood) if it is pulled up," he added.

Swinging the handle to the right extends the right rod farther into its hole. As the handle moves leftward, the right rod, its teeth pressed against the side of the hole, resists pulling up. At the same time, the left rod advances farther into its hole. This action would advance the handle/cutter assembly, by Tom's reckoning.

"This machine would probably not have left a very clean mortise. No doubt some chisel work was necessary to clean it out," he said.


Is the mystery solved?

We'll let that explanation stand for now. But someday, someone will happen across a yellowed instruction booklet for Miller's Patented Mortising Machine. Only then will we know for sure just how this thing is supposed to work.

Machine coutesy of Dick Gowen, Aurora, Nebraska; Photograph: Hetherington Photography


 

shim

Wood Magazine