You are here

Custom neon follows your script

Get your creative juices flowing! Work with a neon artist to create a custom sign that will become the focal point of your man cave.

Submitted by WOOD community member WOOD Magazine StaffSubmit a Shop Guide
  • First, shed some light on the design

    Neon artist Charly Conn, left, discusses the proposed artwork with Allen Darrow, who supplied a concept drawing of his signature on 8 1/2x11" paper.

  • Acrylic forms the back

    With a blade for plastics (Bosch T101BR) mounted in his jigsaw, Charly cuts the 1/2"-thick black acrylic that will become the back panel of the custom neon sign.

  • A quick cleanup

    After peeling the protective paper from the acrylic, he wipes down the sheet with Windex to remove static electricity. The custom vinyl decal is ready to apply.

  • A layer of vinyl adds character

    Charly removes the protective paper from the 48"-long vinyl sheet, then smooths the vinyl with a squeegee. He then sets aside the acrylic.

  • Air pressure prevents pinching

    At the propane-fueled ribbon burner, our artist blows air into the glass tube, preventing it from kinking or becoming restricted while he forms tight bends.

  • Charly checks the curves

    With a full-size reverse pattern on his bench, Charly tweaks each bend in the still-warm glass. He continues pushing air through the blow tube.

  • An electrode insertion

    After heating the end of the first section of tubing, Charly slides an electrode into the tubing. His blow tube prevents the glass from collapsing.

  • Flattening the sign

    Using the flat bench as a reference surface, Charly presses the warm tubing into the same plane. "Wide curves take a lot of time to allow the glass to cool before heating another section," he notes.

  • Another electrode

    As Charly finishes up the first section, he mounts a second electrode in the tubing and checks his work on top of the reversed pattern.

  • Three letters down, three to go

    Nine trips to the ribbon burner and Charly is nearly finished with the first two letters of the second section. Now, he pencils a mark for a section to heat to begin forming the second R.

  • Rounding the final bend

    The last two letters require a second piece of 48"-long glass tubing. After 10 bends, Charly has the two letters formed and then plans placement for another electrode.

  • Clean cuts in glass

    To splice the two sections of lettering, Charly uses an electric glass cutter for a clean, precise cut. He plans the splices to place them on what will become the back side of the lettering.

  • Splicing the cuts

    A hand torch heats up the two sections of glass-tubing union. Once again, the blow tube and cork prevent the interior of the glass tubing to be joined from closing.

  • A final pattern check

    After joining the two sections of tubing, Charly checks the letters against the pattern one final time. He creates a full-size pattern like the one above for every sign passing through his shop.

  • Time for a test light

    After removing air from the glass and then pumping in argon, Charly burns-in the lettering to achieve full brightness.

  • Blacking out the spaces

    Charly brushes on a fast-drying block-out paint, formulated for glass and high in pigments, to the tubing between neon letters. When illuminated, this creates the illusion of separate characters.

  • Trimming out the sign

    For a finished look, Charly edges the acrylic back with 1"-wide acrylic trim. He uses a heat gun to create tight bends. To weld the band to the acrylic, he flows on a thin bead of methylene chloride.

  • Supports offset the tubing

    After drilling a 1/8" hole in the acrylic, Charly attaches clear 1 3/4" tube supports to the sign. This design, using about 17' of tubing, gets two supports on the arrowhead, and 13 tube supports total.

  • Power it up

    With the neon tubing secured on the tube supports, Charly fits an electrode boot that joins an electrode and a specialty cord capable of handling high voltage that leads to the transformer.

  • The finished product

    Allen couldn't be more pleased with the final products—so tickled, he asked Charly to build an identical neon sign for his shop. "It's exciting to see my autograph in neon," Allen says. "I love almost every neon sign I see, but no one has a sign like this!"

Read more about

Tip of the Day

Nix big chips with a homemade separator

Nix big chips with a homemade separator

Dust collectors keep your shop clean, but big chips fill up the bags rapidly. Cyclone separators... read more

Talk in Shop Setup and Design